DSPIC30F5015-20E/PT Microchip Technology, DSPIC30F5015-20E/PT Datasheet - Page 77

• Manufacturer Part Number: DSPIC30F5015-20E/PT
• Description: IC,DSP,16-BIT,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5015-20E/PT

• Rohs Compliant: YES
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Size: 66KB (22K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-TFQFP
• Package: 64TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 52
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 16-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC30F008 - MODULE SKT FOR DSPIC30F 64TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.0
This section describes the second 32-bit General
Purpose (GP) Timer module (Timer4/5) and associated
operational modes. Figure 11-1 depicts the simplified
block diagram of the 32-bit Timer4/5 Module.
Figure 11-2 and Figure 11-3 show Timer4/5 configured
as two independent 16-bit timers, Timer4 and Timer5,
respectively.
FIGURE 11-1:
© 2007 Microchip Technology Inc.
Note: This data sheet summarizes features of this
group of dsPIC30F devices and is not intended to be
a complete reference source. For more information
on the CPU, peripherals, register descriptions and
general device functionality, refer to the “dsPIC30F
Family Reference Manual” (DS70046).
Note:
Note:
T5IF
Event Flag
TIMER4/5 MODULE
T4CK
Timer4 is a Type B timer and Timer5 is a
Type C timer. Please refer to the appropri-
ate timer type in Section 24.0 "Electrical
Characteristics" of this document.
Data Bus<15:0>
(T4CON<6>)
Timer Configuration bit T45, T4CON(<3>) must be set to ‘
control bits are respective to the T4CON register.
Read TMR4
TGATE
Write TMR4
0
1
32-BIT TIMER4/5 BLOCK DIAGRAM
Reset
Equal
16
TMR5HLD
MSB
TMR5
PR5
Comparator x 32
16
16
TMR4
LSB
PR4
Q
Q
CK
D
Gate
Sync
T
CY
TGATE(T4CON<6>)
dsPIC30F6010A/6015
The Timer4/5 module is similar in operation to the
Timer2/3
differences, which are listed below:
• The Timer4/5 module does not support the ADC
• Timer4/5 can not be utilized by other peripheral
The operating modes of the Timer4/5 module are
determined by setting the appropriate bit(s) in the 16-bit
T4CON and T5CON SFRs.
For 32-bit timer/counter operation, Timer4 is the lsw
and Timer5 is the msw of the 32-bit timer.
Event Trigger feature
modules such as Input Capture and Output Compare
Note:
1
’ for a 32-bit timer/counter operation. All
1 x
0 1
0 0
module.
For 32-bit timer operation, T5CON control
bits are ignored. Only T4CON control bits
are used for setup and control. Timer4
clock and gate inputs are utilized for the
32-bit timer module, but an interrupt is
generated with the Timer5 Interrupt Flag
(T5IF) and the interrupt is enabled with the
Timer5 Interrupt Enable bit (T5IE).
Sync
TON
However,
TCKPS<1:0>
1, 8, 64, 256
Prescaler
2
there
DS70150C-page 75
are
some