DSPIC30F3010-20E/ML Microchip Technology, DSPIC30F3010-20E/ML Datasheet - Page 15
![IC,DSP,16-BIT,CMOS,LLCC,44PIN,PLASTIC](/photos/6/81/68122/150-44-qfn_sml.jpg)
DSPIC30F3010-20E/ML
Manufacturer Part Number
DSPIC30F3010-20E/ML
Description
IC,DSP,16-BIT,CMOS,LLCC,44PIN,PLASTIC
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F3010-30ISO.pdf
(228 pages)
4.DSPIC30F3010-30ISO.pdf
(18 pages)
5.DSPIC30F3010-30ISO.pdf
(6 pages)
6.DSPIC30F3010-30ISO.pdf
(16 pages)
7.DSPIC30F3010-30ISO.pdf
(22 pages)
Specifications of DSPIC30F3010-20E/ML
Rohs Compliant
YES
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
24KB (8K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
44-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT44QFN4 - SOCKET TRANS ICE 28DIP TO 44QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
21. Module: I
22. Module: I/O Port
23. Module: ADC
© 2010 Microchip Technology Inc.
If there are two I
them is acting as the Master receiver and the other
as the Slave transmitter. If both devices are config-
ured for 10-bit addressing mode, and have the
same value in the A10 and A9 bits of their
addresses, then when the Slave select address is
sent from the Master, both the Master and Slave
acknowledge it. When the Master sends out the
read operation, both the Master and the Slave
enter into Read mode and both of them transmit
the data. The resultant data will be the ANDing of
the two transmissions.
Work around
In all I
A10 and A9 should be different.
Affected Silicon Revisions
If the user application enables the auto-baud
feature in the UART module, the I/O pin
multiplexed with the IC1 (Input Capture) pin cannot
be used as a digital input. However, the external
interrupt function (INT1) can be used.
Work around
None.
Affected Silicon Revisions
If the user application uses the internal reference
voltage (AV
greater than what is specified in the device data
sheet.
Work around
As an alternative, use the external reference
voltage (V
Affected Silicon Revisions
A0
A0
A0
X
X
X
2
C devices, the addresses as well as bits
A1
A1
A1
X
X
X
REF
DD
2
C
-, V
A2
A2
, AV
A2
X
X
X
REF
2
SS
C devices on the bus, one of
), the ADC has an offset error
+).
24. Module: PWM
25. Module: Timer
26. Module: PLL
If the PTDIR bit is set (when PTMR is counting
down), and the CPU execution is halted (after a
breakpoint is reached), PTMR will start counting
up as if PTDIR was zero.
Work around
None.
Affected Silicon Revisions
When the timer is being operated in Asynchronous
mode using the secondary oscillator (32.768 kHz)
and the device is put into Sleep mode, a clock
switch to any other oscillator mode before putting
the device to Sleep prevents the timer from waking
the device from Sleep.
Work around
Do not clock switch to any other oscillator mode if
the timer is being used in Asynchronous mode
using the secondary oscillator (32.768 kHz).
Affected Silicon Revisions
The PLL LOCK Status bit (OSCCON<5>) can
occasionally get cleared and generate an
oscillator failure trap even when the PLL is still
locked and functioning correctly.
Work around
The user application must include an oscillator
failure Trap Service Routine (TSR). In the trap
service routine, first inspect the status of the Clock
Failure Status bit (OSCCON<3>). If this bit is clear,
return from the trap service routine immediately
and continue program execution.
Affected Silicon Revisions
A0
A0
A0
X
X
X
A1
A1
A1
dsPIC30F3010/3011
X
X
X
A2
A2
A2
X
X
X
DS80449D-page 15