LPC2106FBD48/01 NXP Semiconductors, LPC2106FBD48/01 Datasheet - Page 29
![IC, MCU, 32BIT, 128K FLASH, 48LQFP](/photos/19/0/190032/ge48lqfp05-40_sml.jpg)
LPC2106FBD48/01
Manufacturer Part Number
LPC2106FBD48/01
Description
IC, MCU, 32BIT, 128K FLASH, 48LQFP
Manufacturer
NXP Semiconductors
Datasheet
1.LPC2105FBD48.pdf
(41 pages)
Specifications of LPC2106FBD48/01
Controller Family/series
ARM7
No. Of I/o's
32
Ram Memory Size
64KB
Cpu Speed
60MHz
No. Of Timers
3
No. Of Pwm
RoHS Compliant
Core Size
32bit
Program Memory Size
128KB
Oscillator Type
Internal, External
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC2106FBD48/01
Manufacturer:
NXP
Quantity:
670
Company:
Part Number:
LPC2106FBD48/01
Manufacturer:
NXP
Quantity:
7 750
Company:
Part Number:
LPC2106FBD48/01,15
Manufacturer:
NXP
Quantity:
250
Company:
Part Number:
LPC2106FBD48/01,15
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
Table 9.
T
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Applies to P0[31:22].
[11] SPI is enabled and SSP is disabled in the PCONP register ( see LPC2104/2105/2106 user manual ).
[12] To V
LPC2104_2105_2106_7
Product data sheet
Symbol
Oscillator pins
V
V
amb
i(XTAL1)
o(XTAL2)
Typical ratings are not guaranteed. The values listed are at room temperature (+25 C), nominal supply voltages.
Internal rail.
External rail.
Including voltage on outputs in 3-state mode.
V
3-state outputs go into 3-state mode when V
Accounts for 100 mV voltage drop in all supply lines.
Allowed as long as the current limit does not exceed the maximum current allowed by the device.
Minimum condition for V
= 0 C to +70 C for commercial applications, unless otherwise specified.
DD(3V3)
SS
.
Parameter
input voltage on pin XTAL1
output voltage on pin
XTAL2
Static characteristics
supply voltages must be present.
8.1 Power consumption measurements for LPC2104/2105/2106/01
The power consumption measurements represent typical values for the given conditions.
The peripherals were enabled through the PCONP register, but for these measurements
the peripherals were not configured to run. Power measurements with all peripherals
enabled were performed with the SPI enabled and the SSP disabled. Peripherals were
disabled through the PCONP register. Refer to the LPC2104/2105/2106 User Manual for a
description of the PCONP register.
I
Fig 5.
= 4.5 V, maximum condition for V
I
DD(act)
(mA)
…continued
60
40
20
Test conditions: Active mode entered executing code from on-chip flash; PCLK =
T
Typical LPC2104/2105/2106/01 I
0
amb
12
= 25 C; core voltage 1.8 V.
Conditions
DD(3V3)
is grounded.
Rev. 07 — 20 June 2008
I
= 5.5 V.
28
all peripherals disabled
all peripherals enabled
DD(act)
measured at different frequencies
Min
0
0
LPC2104/2105/2106
Single-chip 32-bit microcontrollers
44
frequency (MHz)
Typ
-
-
[1]
002aad709
© NXP B.V. 2008. All rights reserved.
Max
1.8
1.8
CCLK
60
4
;
29 of 41
Unit
V
V