A29040BL-70F AMIC, A29040BL-70F Datasheet
A29040BL-70F
Specifications of A29040BL-70F
Available stocks
Related parts for A29040BL-70F
A29040BL-70F Summary of contents
Page 1
... Add the product spec of -U series (-40°C ~85°C) 1.0 Final version release (January, 2007, Version 1.0) A29040B Series 512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory Issue Date January 14, 2004 July 6, 2004 December 6, 2004 January 4, 2007 AMIC Technology, Corp. Remark Preliminary Final ...
Page 2
... True background erase can thus be achieved. Power consumption is greatly reduced when the device is placed in the standby mode. 1 A29040B Series ( Data Polling) and 7 AMIC Technology, Corp. ...
Page 3
... VCC 8 A18 9 A16 10 A15 11 A12 (January, 2007, Version 1.0) PLCC VCC A17 30 A14 29 A7 A13 A11 A10 I I I/O 3 A29040BV 2 A29040B Series 5 A14 29 6 A13 A29040BL A11 A10 I AMIC Technology, Corp A10 CE I/O 7 I/O 6 I/O 5 I/O 4 I/O 3 VSS I/O 2 I ...
Page 4
... A0 - A18 Address Inputs I/O - I/O Data Inputs/Outputs 0 7 Chip Enable CE Write Enable WE Output Enable OE VSS Ground VCC Power Supply 3 A29040B Series I/O Input/Output Chip Enable Output Enable STB Data Latch Logic Y-Decoder X-decoder Cell Matrix Description AMIC Technology, Corp Buffers Y-Gating ...
Page 5
... Table 1. A29040B Device Bus Operations VCC ± 0 12.0 ± 0.5V Don't Care A29040B Series ) . . . . . . . . . …… 0°C to +70° …….. -40°C to +85° – A18 High High High-Z = Data In Data Out Address In IN OUT IN AMIC Technology, Corp OUT D IN ...
Page 6
... The device enters the TTL standby held The device requires the IH ) before it is ready to read data input output from the device is IH Address Range 00000h - 0FFFFh 10000h - 1FFFFh 20000h - 2FFFFh 30000h - 3FFFFh 40000h - 4FFFFh 50000h - 5FFFFh 60000h - 6FFFFh 70000h - 7FFFFh AMIC Technology, Corp. read ...
Page 7
... Erase Suspend mode, the 6 A29040B Series - I See "Command Definitions" for details on using ID Identifier Code I 37h 86h IL IH 01h (protected 00h (unprotected 7Fh and during power up, the whichever happens first. Refer to the AMIC Technology, Corp. .To access the ...
Page 8
... Note : See the appropriate Command Definitions table for program command sequence. 7 A29040B Series or I "1", or cause the 5 START Write Program Command Sequence Data Poll from System Embedded Program algorithm in progress Verify Data ? Yes Last Address ? Yes Programming Completed Figure 1. Program Operation AMIC Technology, Corp. . See "Write No ...
Page 9
... Resume command are ignored. Another Erase Suspend command can be written after the device has resumed erasing. 8 A29040B Series , I I/O . Refer to "Write The system can use I I See "Write Operation or I/O status bits, just 7 6 AMIC Technology, Corp. and I Status" for ...
Page 10
... System No Data = FFh ? Erasure Completed Note : 1. See the appropriate Command Definitions table for erase command sequences. 2. See "I/O : Sector Erase Timer" for more information. 3 Figure 2. Erase Operation (January, 2007, Version 1.0) Embedded Erase algorithm in progress Yes 9 A29040B Series AMIC Technology, Corp. ...
Page 11
... AA 2AA 55 555 6 555 AA 2AA 55 555 6 555 AA 2AA 55 555 1 XXX B0 1 XXX 30 10 A29040B Series Third Fourth Fifth 90 X00 37 90 X01 86 90 X03 X02 555 AA 2AA 55 80 555 AA 2AA pulse, whichever happens first. AMIC Technology, Corp. Sixth 555 pulse, goes high 5 ...
Page 12
... During chip erase, a valid address is any non-protected sector address. should be rechecked even if I/O = "1" because 7 5 I/O may change simultaneously with I Figure 3. Data Polling Algorithm AMIC Technology, Corp. PASS . ...
Page 13
... This is a failure condition that 5 failure condition may appear if the system tries determine whether or not an erase 3 switches from "0" to "1." The system may 3 if the system can guarantee that the time between 3 AMIC Technology, Corp. and I the following ...
Page 14
... No Toggle Bit = Toggle ? Yes No I Yes Read I (Notes 1,2) Twice No Toggle Bit = Toggle ? Yes Program/Erase Program/Erase Operation Not Commplete, Write Reset Command toggling. See text. changes to "1". See text. Figure 4. Toggle Bit Algorithm AMIC Technology, Corp. Operation Commplete 5 ...
Page 15
... Table 5. Write Operation Status I/O I/O 7 (Note 1) Toggle I Toggle 1 No toggle Data Data Toggle I/O 7 20ns -2.0V 20ns 20ns 20ns 14 A29040B Series I/O I (Note N/A Data Data 0 N/A 20ns 20ns AMIC Technology, Corp. I/O 2 (Note 1) No toggle Toggle Toggle Data N/A ...
Page 16
... V 2.0 VCC+0.5 V 10.5 12.5 V 0.45 V 2.4 V Min. Typ. Max. Unit ±1.0 µA µA 100 ±1.0 µ µ -0.5 0.8 V 0.7 x VCC VCC+0.3 V 10.5 12.5 V 0.45 V 0.85 x VCC V VCC-0.4 V AMIC Technology, Corp. ...
Page 17
... OE WE Output 0V (January, 2007, Version 1.0) Description Test Setup Read Toggle and Data Polling t RC Addresses Stable t ACC OEH t CE High-Z 16 A29040B Series Speed -55 -70 -90 Min Max Max Max Min Min Max Max Min Output Valid AMIC Technology, Corp. Unit High-Z ...
Page 18
... See the "Erase and Programming Performance" section for more information. (January, 2007, Version 1.0) Description WE low) 17 A29040B Series Speed -55 -70 -90 Min Min. 0 Min Min Min. 0 Min. 0 Min. 0 Min. 0 Min. 0 Min Min. 20 Max. 50 Typ. 7 Typ. 1 Min. 50 AMIC Technology, Corp. Unit µs µs sec µs ...
Page 19
... Note : SA = Sector Address Valid Address for reading status data. (January, 2007, Version 1. WPH A0h 555h for chip erase WPH 55h 30h 10h for chip erase 18 A29040B Series Read Status Data (last two cycles WHWH1 D Status OUT Read Status Data WHWH2 In Complete Progress AMIC Technology, Corp. ...
Page 20
... OH Valid Status Valid Status (first read) (second read) . Illustration shows first two status cycle after command sequence, last status 6 19 A29040B Series VA High-Z Valid Data True High-Z True Valid Data VA VA Valid Status Valid Status (stop togging) AMIC Technology, Corp. ...
Page 21
... Read Program and I/O 6 Description Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Typ. Typ. 20 A29040B Series Erase Resume Erase Erase Suspend Erase Read Complete in the section "Write Operation Statue" for 2 Speed -55 -70 - AMIC Technology, Corp. Unit µs sec ...
Page 22
... Typ. (Note 1) Max. (Note 300 3.6 10.8 for further information A29040B Series PA t WHWH1 or 2 I/O D OUT 7 = Complement of Data Input Array Data. 7 OUT Unit Comments sec Excludes 00h programming prior to erasure (Note 4) sec µs Excludes system-level overhead (Note 5) sec AMIC Technology, Corp. ...
Page 23
... Minimum Pattern Data Retention Time (January, 2007, Version 1.0) Description Test Setup Test Setup Test Conditions 150°C 125°C 22 A29040B Series Min. -1.0V VCC+1.0V -100 mA +100 mA Typ. Max 7 8.5 12 OUT Typ. Max OUT Min 10 Years 20 Years AMIC Technology, Corp. Max. Unit Unit Unit ...
Page 24
... Device Under Test (January, 2007, Version 1.0) Table 6. Test Specifications - 0.0 - 3.0 1.5 1.5 5 6.2 KΩ L Figure 7. Test Setup 23 A29040B Series All others Unit 1 TTL gate 100 0.45 - 2.4 V 0.8, 2.0 V 0.8, 2.0 V 2.7 KΩ Diodes = IN3064 or Equivalent AMIC Technology, Corp. ...
Page 25
... Ordering Information Access Time Part No. (ns) A29040B-55 A29040B-55F A29040BL-55 A29040BL-55F A29040BV-55 A29040BV-55F 55 A29040B-55U A29040B-55UF A29040BL-55U A29040BL-55UF A29040BV-55U A29040BV-55UF A29040B-70 A29040B-70F A29040BL-70 A29040BL-70F A29040BV-70 A29040BV-70F 70 A29040B-70U A29040B-70UF A29040BL-70U A29040BL-70UF A29040BV-70U A29040BV-70UF (January, 2007, Version 1.0) Active Read Program/Erase Current Current Typ. (mA) Typ. (mA ...
Page 26
... Ordering Information (continued) Access Time Part No. (ns) A29040B-90 A29040B-90F A29040BL-90 A29040BL-90F A29040BV-90 A29040BV-90F 90 A29040B-90U A29040B-90UF A29040BL-90U A29040BL-90UF A29040BV-90U A29040BV-90UF (January, 2007, Version 1.0) Active Read Program/Erase Current Current Typ. (mA) Typ. (mA A29040B Series Standby Current Package Typ. (µA) 32Pin DIP 32Pin Pb-Free DIP ...
Page 27
... 0.100 - L 0.120 0.130 0.140 3.048 θ - 0° 15° 0° 26 A29040B Series unit: inches/ θ Dimensions in mm Nom Max - - 5.334 - - 3.912 4.039 - 0.457 - - 1.270 - - 0.254 - 41.91 42.037 13.767 13.894 15.240 15.494 16.510 17.018 - 2.540 - 3.302 3.556 - 15° AMIC Technology, Corp. ...
Page 28
... A29040B Series unit: inches/ θ Dimensions in mm Min Nom Max - - 3. 2.80 2.93 0.71 0.81 0.46 0.54 0.254 0.35 13.97 14.05 11.43 11.51 1.27 1.42 12.95 13.46 10.41 10.92 14.99 15.11 12.45 12.57 2.29 2. 0.075 0° - 10° AMIC Technology, Corp. ...
Page 29
... A29040B Series unit: inches/ Detail "A" Dimensions in mm Min Nom Max - - 1.20 - 0.15 1.00 1.05 0.22 0.27 - 0.20 18.40 18.50 - 8.00 8.10 0.50 BSC 20.00 20.20 0.50 0. 0.08 - 0° 5° AMIC Technology, Corp. θ ...