78Q8430-100CGT/F TERIDIAN, 78Q8430-100CGT/F Datasheet - Page 5

• Manufacturer Part Number: 78Q8430-100CGT/F
• Description: IC, ETHERNET TXRX, IEEE 802.3, LQFP-100
• Manufacturer: TERIDIAN

Specifications of 78Q8430-100CGT/F

• No. Of Ports: 2
• Ethernet Type: IEEE 802.3x, IEEE 802.3u, IEEE 802.3-2000
• Ic Interface Type: Host Bus, JTAG
• Supply Voltage Range: 0V To 3.3V
• Operating Temperature Range: 0°C To +70°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MEDIA INDEPENDENT INTERFACE
MII Transmit and Receive Operation
The MII interface on the 78Q2123/78Q2133 provide
independent transmit and receive paths for both
10Mb/s and 100Mb/s data rates as described in
Clause 22 of the IEEE-802.3 standard.
The transmit clock, TX_CLK, provides the timing
reference for the transfer of TX_EN, TXD3-0, and
TX_ER
78Q2123/78Q2133.
rising edge of TX_CLK when TX_EN is asserted.
TX_ER is also captured on the rising edge of
TX_CLK and is asserted by the MAC to request that
an error code group is to be transmitted.
assertion
78Q2123/78Q2133 are operating in 10BASE-T
mode.
The receive clock, RX_CLK, provides the timing
reference to transfer RX_DV, RXD3-0, and RX_ER
signals from the 78Q2123/78Q2133 to the MAC.
RX_DV transitions synchronously with respect to
RX_CLK
78Q2123/78Q2133 are presenting valid data on
RXD3-0. RX_ER is asserted and is synchronous to
RX_CLK when a code group violation has been
detected in the current receive packet.
Station Management Interface
The station management interface consists of
circuitry which implements the serial protocol as
described in Clause 22.2.4.4 of IEEE-802.3. A 16-
bit shift register receives serial data applied to the
MDIO pin at the rising-edge of the MDC clock signal.
Once
management control logic looks for the start-of-
frame sequence and a read or write op-code,
followed by the PHYAD and REGAD fields.
default address for the 78Q2123/78Q2133 is 1. For
a read operation, the MDIO port becomes enabled
as an output and the register data is loaded into a
shift
78Q2123/78Q2133
preamble rather than the 32 bits prescribed by IEEE-
802.3. This allows for faster programming of the
registers. If a register does not exist at an address
indicated by the REGAD field or if the PHYAD field
does not match the 78Q2123/78Q2133 PHYAD, a
read of the MDIO port will return all ones. For a
write operation, the data is shifted in and loaded into
the appropriate register after the sixteenth data bit
has been received.
supported by the 78Q2123/78Q2133 are ignored.
Page: 5 of 39
the preamble
register
signals
of
and
TX_ER
for
is
from
can
TXD3-0 is captured on the
is
Writes to registers not
is
asserted
transmission.
work
the
received, the
ignored
with
MAC
when
when
a
©
2006 Teridian Semiconductor Corporation
to
one-bit
station
The
The
The
the
the
the
LED STATE INDICATION
When the PHYAD field is all zeros, the Station
Management Entity (STA) is requesting a broadcast
data transaction.
Management
broadcast request.
respond to the broadcast data transaction.
ADDITIONAL FEATURES
LED Indicators
There are two LED pins that can be used to indicate
various
78Q2123/78Q2133. The function of these pins is
programmable via the MR23 register as shown in
the table below:
The default status of these LEDs are “Link OK” for
LED0 and “RX or TX Activity” for LED1.
Interrupt Pin
The 78Q2123/78Q2133 have an Interrupt pin (INTR)
that is asserted whenever any of the eight interrupt
bits of MR17.7:0 are set. These interrupt bits can be
disabled via the MR17.15:8 Interrupt Enable bits.
The Interrupt Polarity bit, MR16.14, controls the
active level of the INTR pin. When the INTR pin is
not asserted, the pin is held in a high impedance
state. An external pull-up or pull-down resistor may
be required for use with the INTR pin.
0
1
2
3
4
5
6
7
8
states
78Q2123/78Q2133 MicroPHY™
1 = Link OK (Default LED0)
1 = RX or TX Activity (Default LED1)
1 = TX Activity
1 = RX Activity
1 = Collision
1 = 100 BASE-TX mode
1 = 10 BASE-T mode
1 = Full Duplex
1= Link OK & Blink = RX or TX Activity
10/100BASE-TX Transceiver
Interface
All PHYs sharing the same
of
The 78Q2123/78Q2133 will
must
operation
respond
of
to
Rev 1.1
this
the