PMN8118UWP Ericsson Power Modules, PMN8118UWP Datasheet - Page 42

• Manufacturer Part Number: PMN8118UWP
• Description: DC/DC Converters & Regulators 0.7-3.6V 30A Non-Iso Input 5.5-14V 108W
• Manufacturer: Ericsson Power Modules
• Series: PMNr

Specifications of PMN8118UWP

• Output Power: 108 W
• Input Voltage Range: 5.5 V to 14 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 0.7 V to 3.6 V
• Output Current (channel 1): 30 A
• Output Type: POLA Non-Isolated Regulator
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Connections
E
Pin Designation
1
2
3
4
5
6
Prepared (also subject responsible if other)
EYIPYAN
Approved
SEC/D (Julia You)
PMN 8000 series PoL Regulator
Input 5.5 - 14 V, Output up to 30 A / 108 W
Inhibit/
UVLO Adjust
V
GND
GND
V
V
I
o
I
Function
The Inhibit pin is an open-
collector/drain, negative logic input
that is referenced to GND. Applying a
low level ground signal to this input
disables the module’s output voltage.
If the Inhibit pin is left open-circuit,
the module produces an output
whenever a valid input source is
applied. This input is not compatible
with TTL logic devices and should not
be tied V
This pin is also used for input
The positive input voltage power node
to the module, which is referenced to
common GND
This is the common ground connection
for the V
is also the 0 V
control inputs
This is the common ground connection
for the V
is also the 0 V
control inputs
The regulated positive power output
with respect to the GND.
The positive input voltage power node
to the module, which is referenced to
common GND.
I
I
I
and V
and V
or other voltage.
dc
dc
o
o
reference for the
reference for the
power connections. It
power connections. It
Checked
EQUENXU
Ericsson Internal
PRODUCT SPECIFICATION
No.
3/1301-BMR656 8118 Uen
Date
2007-7-9
7
8
9
10
11
12
13
GND
GND
V
+Sense
-Sense
V
Turbo Trans
o
o
Adjust
Technical Specification
EN/LZT 146 387 R1B December 2009
© Ericsson AB
Rev
B
This is the common ground connection
for the V
is also the 0 V
control inputs
This is the common ground connection
for the V
is also the 0 V
control inputs
The regulated positive power output
with respect to the GND.
The sense input allows the regulation
circuit to compensate for voltage drop
between the module and the load. For
optimal voltage accuracy, +Sense must
The sense input allows the regulation
circuit to compensate for voltage drop
between the module and the load. For
optimal voltage accuracy, -Sense must
be connect GND(pin 8) very close to
A 0.1 W 1% resistor must be directly
connected between this pin and pin 8
(GND) to set the output voltage to a
value higher than 0.7 V. The
temperature stability of the resistor
should be 100 ppm/℃ (or better). The
setpoint range for the output voltage
is from 0.7V to 3.6V. If left open
circuit, the output voltage defaults to
its lowest value. For further
i f
This input pin adjusts the transient
response of the regulator. To activate
the Turbo Trans
50mW resistor must be connected
between this pin and pin 10 (+Sense)
very close to the module. For a given
value of output capacitance, a
reduction in peak output voltage
deviation is achieved by using this
feature. If unused, this pin must be left
open-circuit. External capacitance must
ti
Reference
I
I
and V
and V
dc
dc
o
o
TM
reference for the
reference for the
power connections. It
power connections. It
t
feature, a 1%,
t
lt
10 (12)
42