A000046 Arduino, A000046 Datasheet - Page 138

• Manufacturer Part Number: A000046
• Description: MCU, MPU & DSP Development Tools Uno
• Manufacturer: Arduino
• Series: -r
• Type: MCUr

Specifications of A000046

• Processor To Be Evaluated: ATmega328
• Interface Type: USB, I2C, SPI
• Dimensions: 2.7 in x 2.1 in
• Operating Supply Voltage: 5 V
• Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega328

15.11.4
15.11.5
15.11.6
15.11.7
8161D–AVR–10/09
TCNT1H and TCNT1L – Timer/Counter1
OCR1AH and OCR1AL – Output Compare Register 1 A
OCR1BH and OCR1BL – Output Compare Register 1 B
ICR1H and ICR1L – Input Capture Register 1
The two Timer/Counter I/O locations (TCNT1H and TCNT1L, combined TCNT1) give direct
access, both for read and for write operations, to the Timer/Counter unit 16-bit counter. To
ensure that both the high and low bytes are read and written simultaneously when the CPU
accesses these registers, the access is performed using an 8-bit temporary High Byte Register
(TEMP). This temporary register is shared by all the other 16-bit registers.
page 115.
Modifying the counter (TCNT1) while the counter is running introduces a risk of missing a com-
pare match between TCNT1 and one of the OCR1x Registers.
Writing to the TCNT1 Register blocks (removes) the compare match on the following timer clock
for all compare units.
The Output Compare Registers contain a 16-bit value that is continuously compared with the
counter value (TCNT1). A match can be used to generate an Output Compare interrupt, or to
generate a waveform output on the OC1x pin.
The Output Compare Registers are 16-bit in size. To ensure that both the high and low bytes are
written simultaneously when the CPU writes to these registers, the access is performed using an
8-bit temporary High Byte Register (TEMP). This temporary register is shared by all the other
16-bit registers.
The Input Capture is updated with the counter (TCNT1) value each time an event occurs on the
ICP1 pin (or optionally on the Analog Comparator output for Timer/Counter1). The Input Capture
can be used for defining the counter TOP value.
Bit
(0x85)
(0x84)
Read/Write
Initial Value
Bit
(0x89)
(0x88)
Read/Write
Initial Value
Bit
(0x8B)
(0x8A)
Read/Write
Initial Value
Bit
(0x87)
(0x86)
Read/Write
Initial Value
See Section “15.3” on page 115.
R/W
R/W
R/W
R/W
7
0
7
0
7
0
7
0
R/W
R/W
R/W
R/W
6
0
6
0
6
0
6
0
ATmega48PA/88PA/168PA/328P
R/W
R/W
R/W
R/W
5
0
5
0
5
0
5
0
R/W
R/W
R/W
R/W
4
0
4
0
4
0
4
0
OCR1A[15:8]
OCR1B[15:8]
TCNT1[15:8]
OCR1A[7:0]
OCR1B[7:0]
TCNT1[7:0]
ICR1[15:8]
ICR1[7:0]
R/W
R/W
R/W
R/W
3
0
3
0
3
0
3
0
R/W
R/W
R/W
R/W
2
0
2
0
2
0
2
0
R/W
R/W
R/W
R/W
1
0
1
0
1
0
1
0
See Section “15.3” on
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
OCR1AH
OCR1BH
OCR1AL
OCR1BL
TCNT1H
TCNT1L
ICR1H
ICR1L
138