LQ121S1LG42 Sharp Microelectronics, LQ121S1LG42 Datasheet
LQ121S1LG42
Specifications of LQ121S1LG42
Related parts for LQ121S1LG42
LQ121S1LG42 Summary of contents
Page 1
...
Page 2
... LQ121S1LG42 SPEC No. DATE LD-20712A July.28.2008 RECORDS OF REVISION REVISED No. PAGE - - SUMMARY - 1 st Issue NOTE ...
Page 3
... Application This specification applies to color TFT-LCD module, LQ121S1LG42 These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 4
Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, control circuit and power supply circuit and a backlight unit. Graphics and ...
Page 5
Input Terminals 4-1. TFT-LCD panel driving CN1 (LVDS signals , +3.3V / +5.0V DC power supply and Contorol signal) Corresponding connector:FI-SE20M (JAE) or FI-S20S (JAE) Pin No. Symbol GND 4 GND 5 ...
Page 6
LVDS Interface block diagram Using receiver Single LVDS interface, which equals THC63LVDF64A(THine),contained in a control IC ： Corresponding Transmitter ：DS90C363, DS90C363A, DS90C383, DS90C383A( THC63LVDF63A,THC63LVDM63A(THine), SN75LVDS84(Ti) （System Side） Controller LVDS Transmitter ６ R0∼R5 TxIN 0∼ 5 ６ G0∼G5 TxIN 6∼11 ...
Page 7
Mapping RXCLKIN+/- RXIN0+/- R1 RXIN1+/- G2 RXIN2+/- B3 4-3. Backlight driving CN2 ,CN3 Used connector : BHR-03VS-1(JST) Corresponding connector :SM02(8.0)B-BHS(JST) Pin no. symbol 1 VHIGH Power supply for lamp (High voltage side This is electrically opened. 3 ...
Page 8
Symbol Parameter Ｖ Supply voltage LVDS Signals Ｖ Ｖ Input voltage Ambient temperature Ｔｏｐａ [Note1]On-off conditions for supply voltage 0<t1≦15ms 0<t2≦10ms 0<t3≦100ms 0<t4≦1s 200ms<t5 Vcc-dip conditions 1) 2.5V≦Vcc<3.0V td≦10ms 2) Vcc<2.5V Vcc-dip conditions should also follow the ...
Page 9
Backlight driving The backlight system is an edge-lighting type with 2 CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. Parameter Symbol Lamp current range Lamp power consumption Lamp frequency Kick-off voltage ...
Page 10
Timing characteristics of input signals 8-1. Timing characteristics (These are specified at the digital inputs/outputs of LVDS transmitter/receiver.) Data ENAB Sync C (Vertical timing) Item(symbol) Vsync cycle ( Vsync pulse width (T Back porch ( ...
Page 11
Phase difference) ENAB Hsync T HN Item Hsync-ENAB Phase difference (T 8-2 Display position Item Horizontal rising edge of ENAB rising edge of Hsync Vertical rising edge of Vsync [Note1] In case that ENAB signal is fixed to low ...
Page 12
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray Gray scale Scale Black - 0 0 ...
Page 13
Optical Characteristics Parameter Symbol Viewing Horizontal θ21, θ22 angle Vertical θ11 range θ12 Contrast ratio CRn CRo Response Rise τr time Decay τd Chromaticity x of white y Chromaticity x of red y Chromaticity x of green y Chromaticity ...
Page 14
The contrast ratio is defined as the following. Contrast Ratio (CR) = [Note3]Definition of response time: The response time is defined as the following figure and shall be measured by switching ...
Page 15
Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. ...
Page 16
Packing form Product country Piling number of cartons Package quantity in one carton Carton size Total mass of one carton filled with full modules Packing form is shown 14.Reliability test items No. Test item 1 High temperature storage test ...
Page 17
... Packing box Label: （４Ｓ）LQ121S1LG42 社内品番： Barcode （１Ｔ）２００８．０７．２３ ＬｏｔＮＯ． ： Barcode （Ｑ） １０ ...
Page 18
...
Page 19
...