ATMEGA64A-MN Atmel, ATMEGA64A-MN Datasheet - Page 272
ATMEGA64A-MN
Manufacturer Part Number
ATMEGA64A-MN
Description
IC MCU AVR 64K FLASH 8QFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet
1.ATMEGA64A-AU.pdf
(392 pages)
Specifications of ATMEGA64A-MN
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
53
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 272 of 392
- Download datasheet (8Mb)
8160C–AVR–07/09
Table 25-5.
Note:
If the ADC is not to be used during scan, the recommended input values from
be used. The user is recommended not to use the Differential Gain stages during scan. Switch-
cap based gain stages require fast operation and accurate timing which is difficult to obtain
when used in a scan chain. Details concerning operations of the differential gain stage is there-
fore not provided.
The AVR ADC is based on the analog circuitry shown in
imation algorithm implemented in the digital logic. When used in Boundary-scan, the problem is
usually to ensure that an applied analog voltage is measured within some limits. This can easily
be done without running a successive approximation algorithm: apply the lower limit on the digi-
tal DAC[9:0] lines, make sure the output from the comparator is low, then apply the upper limit
on the digital DAC[9:0] lines, and verify the output from the comparator to be high.
The ADC needs not be used for pure connectivity testing, since all analog inputs are shared with
a digital port pin as well.
When using the ADC, remember the following:
Signal
Name
SCTEST
ST
VCCREN
• The Port Pin for the ADC channel in use must be configured to be an input with pull-up
• In Normal mode, a dummy conversion (consisting of 10 comparisons) is performed when
• The DAC values must be stable at the midpoint value 0x200 when having the HOLD signal
disabled to avoid signal contention.
enabling the ADC. The user is advised to wait at least 200 ns after enabling the ADC before
controlling/observing any ADC signal, or perform a dummy conversion before using the first
result.
low (Sample mode).
1. Incorrect setting of the switches in
the part. There are several input choices to the S&H circuitry on the negative input of the out-
put comparator in
Bandgap reference source, or Ground.
Boundary-scan Signals for the ADC
Input
Input
Direction
as Seen
from the
ADC
Input
Figure
Description
Switch-cap TEST
enable. Output from
x10 gain stage send
out to Port Pin having
ADC_4
Output of gain stages
will settle faster if this
signal is high first two
ACLK periods after
AMPEN goes high.
Selects Vcc as the
ACC reference
voltage.
25-10. Make sure only one path is selected from either one ADC pin,
Figure 25-10
(1)
Recommended
Input when not
(Continued)
will make signal contention and may damage
Figure 25-10
in Use
0
0
0
with a successive approx-
Recommended Inputs
are Used, and CPU is
ATmega64A
Output Values when
not Using the ADC
Table 25-5
0
0
0
should
272
Related parts for ATMEGA64A-MN
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 64K 16MHZ 5V 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 64K 16MHZ 5V 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 64K 16MHZ COM 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 64K 16MHZ IND 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 64K 16MHZ COM 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 64KB FLASH 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 64KB FLASH 16MHZ 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 64K 16MHZ IND 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 64K 5V 16MHZ 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 64K 5V 16MHZ 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU 8-Bit ATmega AVR RISC 64KB Flash 5V 64-Pin TQFP T/R
Manufacturer:
Atmel
Datasheet: