ATMEGA256RZAV-8AU Atmel, ATMEGA256RZAV-8AU Datasheet - Page 9
![MCU ATMEGA2561/AT86RF230 64-TQFP](/photos/12/13/121332/313-64-tqfp_sml.jpg)
ATMEGA256RZAV-8AU
Manufacturer Part Number
ATMEGA256RZAV-8AU
Description
MCU ATMEGA2561/AT86RF230 64-TQFP
Manufacturer
Atmel
Series
ATMEGAr
Datasheets
1.ATMEGA640V-8CU.pdf
(38 pages)
2.ATMEGA640V-8CU.pdf
(444 pages)
3.AT86RF230-ZU.pdf
(98 pages)
Specifications of ATMEGA256RZAV-8AU
Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Applications
ISM, ZigBee™
Power - Output
3dBm
Sensitivity
-101dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
15.5mA
Current - Transmitting
16.5mA
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 4kB EEPROM, 8kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
64-TQFP
Wireless Frequency
2.4 GHz
Interface Type
JTAG, SPI
Output Power
3 dBm
For Use With
ATAVRISP2 - PROGRAMMER AVR IN SYSTEM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Operating Temperature
-
Data Rate - Maximum
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
ATmega256
Table 5-1. Example Bill of Materials
5131E-MCU Wireless-02/09
Designator
B1
B1
(alternatively)
CB1
CB2
CB3
CB4
CX1
CX2
C1
C2
C3
R1
R2
XTAL
Description
SMD balun
SMD balun / filter
LDO VREG
bypass capacitor
Power supply
decoupling
LDO VREG
bypass capacitor
Power supply
decoupling
Crystal load capacitor
Crystal load capacitor
RF coupling capacitor
RF coupling capacitor
CLKM low-pass
filter capacitor
Pull-down resistor
CLKM low-pass
filter resistor
Crystal
Capacitors CB1 and CB3 are bypass capacitors for the integrated analog and digital
voltage regulators to ensure stable operation (1 µF recommended value). All decoupling
and bypass capacitors should be placed as close as possible to the AT86RF230 pins
and should have a low-resistance and low-inductance connection to ground to achieve
the best performance.
The crystal (XTAL), the two load capacitors (CX1, CX2), and the internal circuitry
connected to pins XTAL1 and XTAL2 form the crystal oscillator. To achieve the best
accuracy and stability of the reference frequency, large parasitic capacitances should
be avoided. Crystal lines should be routed as short as possible and not in proximity of
digital I/O signals.
Crosstalk from digital signals on the crystal pins or the RF pins can degrade the system
performance. Therefore, a low-pass filter (C3, R2) is placed close to the CLKM output
pin to reduce the radiation of signal harmonics. This is not needed if the CLKM pin is
not used. Then the output should be turned off during device initialization.
The application board ground plane should be separated into four independent
fragments, the analog, the digital, the antenna and the XTAL ground plane. The
exposed paddle shall act as reference of the individual grounds.
For further details see application note AVR2005 "Design Considerations for the
AT86RF230".
Value
2.45 GHz
2.45 GHz
1 µF
1 µF
1 µF
1 µF
12 pF
12 pF
22 pF
22 pF
2.2 pF
10 kΩ
680Ω
CX-4025 16 MHz
SX-4025 16 MHz
Manufacturer
Wuerth
Johanson
Technology
AVX
Murata
AVX
Murata
Epcos
Epcos
AVX
AVX
Murata
ACAL Taitjen
Siward
Part Number
748421245
2450FB15L0001
0603YD105KAT2A
GRM188R61C105KA12D
06035A120JA
GRP1886C1H120JA01
B37930
B37920
06035A220JAT2A
06035A229DA
GRP1886C1H2R0DA01
XWBBPL-F-1
A207-011
Comment
2.45 GHz Balun
2.45 GHz Balun / Filter
X5R
(0603)
COG
(0603)
C0G
(0402 or 0603)
COG
(0603)
Designed for f
Recommended 0Ω, if
continuous transmission is
not required
Designed for f
AT86RF230
5%
10%
5%
±0.5 pF 50V
CLKM
CLKM
16V
50V
50V
= 1 MHz
= 1 MHz
9