ATMEGA256RZAV-8AU Atmel, ATMEGA256RZAV-8AU Datasheet - Page 62
![MCU ATMEGA2561/AT86RF230 64-TQFP](/photos/12/13/121332/313-64-tqfp_sml.jpg)
ATMEGA256RZAV-8AU
Manufacturer Part Number
ATMEGA256RZAV-8AU
Description
MCU ATMEGA2561/AT86RF230 64-TQFP
Manufacturer
Atmel
Series
ATMEGAr
Datasheets
1.ATMEGA640V-8CU.pdf
(38 pages)
2.ATMEGA640V-8CU.pdf
(444 pages)
3.AT86RF230-ZU.pdf
(98 pages)
Specifications of ATMEGA256RZAV-8AU
Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Applications
ISM, ZigBee™
Power - Output
3dBm
Sensitivity
-101dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
15.5mA
Current - Transmitting
16.5mA
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 4kB EEPROM, 8kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
64-TQFP
Wireless Frequency
2.4 GHz
Interface Type
JTAG, SPI
Output Power
3 dBm
For Use With
ATAVRISP2 - PROGRAMMER AVR IN SYSTEM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Operating Temperature
-
Data Rate - Maximum
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
ATmega256
9.4 Voltage Regulators (AVREG, DVREG)
9.4.1 Overview
62
AT86RF230
the SPI transfer rate shall be lower than 250 Kbit/s to ensure no TRX_UR interrupt
occurs.
Note, during the Frame Buffer read access the TRX_UR interrupt is first valid 64 µs
after the RX_START interrupt. The occurrence of the interrupt can be disregarded when
reading the first byte of the Frame Buffer between 32 µs and 64 µs after the
RX_START interrupt.
If a received frame upload is delayed and during the upload process a new frame is
received, a TRX_UR and an RX_START interrupt occurs. Even so, the old frame data
can be read, if the SPI data rate is higher than the effective over air data rate. A
minimum SPI clock rate of 1 MHz is recommended in this special case. Finally it is
required to check the uploaded frame data integrity by a FCS using the microcontroller.
When writing data to the Frame Buffer during frame transmission, the SPI transfer rate
shall be higher than 250 Kbit/s to ensure no TRX_UR interrupt occurs. The first byte of
the PSDU data must be available in the Frame Buffer before SFD transmission has
been completed, which takes 176 µs (16 µs PA ramp up + 128 µs preamble
transmission + 32 µs SFD transmission) from the rising edge of SLP_TR pin (see
Figure 7-2).
The main features of the Voltage Regulator modules are:
• Bandgap stabilized 1.8V supply for analog and digital domain.
• Low dropout (LDO) voltage regulator
• Configurable for usage of external voltage regulator
The internal voltage regulators supply the low voltage domains of the AT86RF230. The
AVREG provides the regulated 1.8V supply voltage for the analog section and the
DVREG supplies the 1.8V supply voltage for the digital section. A simplified schematic
of the internal voltage regulator is shown in Figure 9-2.
Figure 9-2. Simplified Schematic of AVREG/DVREG
reference
Bandgap
voltage
1.25V
DEVDD / EVDD
DVDD / AVDD
5131E-MCU Wireless-02/09