SX1211I084TRT Semtech, SX1211I084TRT Datasheet - Page 28

IC SNGL-CHIP TXRX 32-TQFN

SX1211I084TRT

Manufacturer Part Number
SX1211I084TRT
Description
IC SNGL-CHIP TXRX 32-TQFN
Manufacturer
Semtech
Datasheets

Specifications of SX1211I084TRT

Frequency
860 ~ 960MHz
Data Rate - Maximum
200kbps
Modulation Or Protocol
FSK, OOK
Applications
AMR, ISM, Security and Access
Power - Output
12.5dBm
Sensitivity
-113dBm
Voltage - Supply
2.1 V ~ 3.6 V
Current - Receiving
3mA
Current - Transmitting
25mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
32-TQFN
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Modulation Type
FSK/OOK
Package Type
TQFN EP
Operating Supply Voltage (min)
2.1V
Operating Supply Voltage (typ)
2.5/3.3V
Operating Supply Voltage (max)
3.6V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Compliant
Other names
SX1211I084TRT

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SX1211I084TRT
Manufacturer:
HITTITE
Quantity:
560
Part Number:
SX1211I084TRT
0
The effect of the Fdev setting is different between FSK and OOK modes:
In FSK mode the Fdev setting, as configured by MCParam_Freq_Dev, sets sampling frequencies on the receiver.
The user should make it consistent with the frequency deviation of the FSK signal that is received.
The frequency deviation Fdev, as described above, sets the sampling rate of the RSSI block. It is therefore
necessary to set Fdev to the recommended low-IF frequency, IF2, of 100 kHz:
The FSK demodulator provides data polarity information, based on the relative phase of the input I and Q signals at
the baseband. Its outputs can be fed to the Bit Synchronizer to recover the timing information. The user can also
use the raw, unsynchronized, output of the FSK demodulator in Continuous mode.
The FSK demodulator of the SX1211 operates most effectively for FSK signals with a modulation index greater
than or equal to two:
The OOK demodulator performs a comparison of the RSSI output and a threshold value. Three different threshold
modes are available, programmed through the RXParam_OOK_thresh_type register.
The recommended mode of operation is the “Peak” threshold mode, illustrated below in Figure 22:
Rev 7 – Sept 2
ADVANCED COMMUNICATIONS & SENSING
3.4.8. Fdev Setting in Receive Mode
3.4.9. FSK Demodulator
3.4.10. OOK Demodulator
nd
, 2008
RXParam_RSSI_val(7:0)
IRQParam_RSSI_irq
3.4.8.1. FSK Rx Mode
3.4.8.2. OOK Rx Mode
24 26 27 30 25 20 20 20 18 22
Fdev
MCParam
Figure 21: RSSI IRQ Timings
IF
2
_
Freq
Page 28 of 92
100
2
*
BR
Fdev
kHz
_
dev
Clear interrupt
"
2
00000011
"
33
20 22 34
33
www.semtech.com
SX1211

Related parts for SX1211I084TRT