20-101-1221 Rabbit Semiconductor, 20-101-1221 Datasheet - Page 46
![RCM4400W (JAPAN TELEC CERTIFIED)](/photos/14/19/141972/20-101-1221_sml.jpg)
20-101-1221
Manufacturer Part Number
20-101-1221
Description
RCM4400W (JAPAN TELEC CERTIFIED)
Manufacturer
Rabbit Semiconductor
Series
RabbitCore®r
Datasheet
1.20-101-1202.pdf
(126 pages)
Specifications of 20-101-1221
Frequency
2.4GHz
Modulation Or Protocol
802.11 b
Power - Output
16dBm
Voltage - Supply
3.3V
Current - Receiving
450mA
Current - Transmitting
450mA
Data Interface
Connector, 2 x 25 Header
Memory Size
512K Flash, 1MB SRAM
Antenna Connector
SMA
Operating Temperature
-20°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Sensitivity
-
Data Rate - Maximum
-
Other names
316-1147
- Current page: 46 of 126
- Download datasheet (2Mb)
There are two LEDs close to the RP-SMA antenna connector at J3, a green LED at DS1
(
(
An RG316 coaxial cable may be used to extend the antenna up to 30 cm (1 ft). This coaxial
cable has an impedance of 50 Ω and experiences 1.65 dB/m signal loss at 2.4 GHz.
4.2.3 Programming Port
The RCM4400W is programmed via the 10-pin header labeled J2. The programming port
uses the Rabbit 4000’s Serial Port A for communication. Dynamic C uses the programming
port to download and debug programs.
Serial Port A is also used for the following operations.
• Cold-boot the Rabbit 4000 on the RCM4400W after a reset.
• Fast copy designated portions of flash memory from one Rabbit-based board (the
Alternate Uses of the Programming Port
All three Serial Port A signals are available as
• a synchronous serial port
• an asynchronous serial port, with the clock line usable as a general CMOS I/O pin
The programming port may also be used as a serial port via the
programming cable.
In addition to Serial Port A, the Rabbit 4000 startup-mode (SMODE0, SMODE1),
STATUS, and reset pins are available on the programming port.
The two startup-mode pins determine what happens after a reset—the Rabbit 4000 is
either cold-booted or the program begins executing at address 0x0000.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose output once a program has been downloaded and
The reset pin is an external input that is used to reset the Rabbit 4000.
Refer to the
40
LINK
ACT
master) to another (the slave) using the Rabbit Cloning Board.
is running.
) to indicate activity.
) to indicate association with the Wi-Fi access point, and a yellow LED at DS2
Rabbit 4000 Microprocessor User’s Manual
for more information.
DIAG
RabbitCore RCM4400W
connector on the
Related parts for 20-101-1221
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![20-101-0575](/photos/6/75/67539/20-101-0575_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0576](/photos/37/60/376010/bl2500_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0412](/photos/37/60/376043/101-0412_tmb.jpg)
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0411](/photos/37/60/376043/101-0412_tmb.jpg)
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0457](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
![20-101-0455](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
![20-101-0497](/photos/37/60/376011/op6800_rgb_tmb.jpg)
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0456](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
![20-101-0591](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
![20-101-0594](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
![20-101-0602](/photos/37/60/376010/bl2500_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0430](/photos/37/60/376012/bl20_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
![20-101-0462](/photos/37/60/376013/bl2100_600_tmb.jpg)
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
![20-101-0891](/photos/37/60/376014/bl2600_600_tmb.jpg)
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
![20-101-0654](/photos/37/60/376011/op6800_rgb_tmb.jpg)
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: