MTCMR-G-F4 Multi-Tech Systems, MTCMR-G-F4 Datasheet - Page 168

• Manufacturer Part Number: MTCMR-G-F4
• Description: MODEM GPRS QUAD BAND GSM GLOBAL
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® iCellr

Specifications of MTCMR-G-F4

• Frequency: 850MHz, 900MHz, 1.8GHz, 1.9GHz
• Applications: General Purpose
• Interface: RS-232, USB
• Function: Transceiver, Modem
• Data Rate - Maximum: 115.2kbps
• Modulation Or Protocol: GSM, GPRS
• Voltage - Supply: 9 V ~ 32 V
• Package / Case: Module with Case
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Power - Output: -
• Sensitivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 881-1151; MTCMR-G-F4

GPRS Parameters Customization +WGPRS
Multi-Tech Systems, Inc. GPRS AT Commands Reference Guide (Document Number S000293J)
Description:
Values:
Notes:
When the modem is set in CG class, the modem always makes an automatic GPRS attachment after
initialization. AT+WGPRS? always gives +WGPRS: 0,0 for the parameter 0.
The default value for mode 7 is 0. In this case, no automatic GPRS reconnection to a new operator is done
when reaching border areas.
This command modifies some of the GPRS parameters:
In addition, this command allows you to:
Important Note:
and 7 (refer to the Values section).
<parameter> A numeric parameter that controls the operation defined by <mode> if it is equal to 0, 1, 2
<cid>
<class>
<mode>
•
•
•
•
•
0
1
2
3
4
5
6
7
Notes:
0
1
The ATTACH-STATUS (the modem doesn’t automatically make a GPRS attachment after
initialization)
The PDP-INIT-STATUS (activate automatically some defined PDP Contexts after initialization)
and
The user-defined multislot class. This parameter represents the GPRS class chosen by the user
Automatically set some defined PDP contexts to be activated after initialization.
Set some parameters for the PALM® OS software: PPP Silent Mode (PPP waits for PPP Client
to perform power saving (by reducing TX [or uplink] time slots).
to start the dialog) and Slow CONNECT due to the delay of the processing of PALM® OK, the
CONNECT is sent one second after the dialing command request.
•
•
•
•
If <mode>=0, 1, 3, 4, 5, 6 or 7 <cid> and <class> will be ignored.
If <mode>=0, 1, 2, 3, 5, or 6 <class> will be ignored.
A numeric parameter which specifies a GPRS parameter:
ATTACH-STATUS (the modem doesn’t automatically make a GPRS attachment after init)
PDP-INIT-STATUS (declare some PDP contexts liable to be activated automatically after
initialization by <mode>=2)
Set “ACTIVABLE” automatically after init a define PDP context
PPP silent mode
Definition of the GPRS multislot class
Slow CONNECT for PALM® OS
PPP Filtering
Automatic GPRS roaming inter-operator: if activated, the modem automatically re-
attaches itself to the network and reactivates its PDP context by changing the operator
when reaching border areas.
If <mode>=4 <parameter> and <cid> will be ignored. The modem must be restarted to
take the modification into account.
PPP Filtering is a test-purpose functionality. It avoids sending some OS-specific frames on
the radio link, for accurate transfer rate measurements.
or 3
Operation Off (disabled)
Operation On (enabled)
(PDP Context Identifier). A numeric parameter that specifies a particular PDP context
definition. The parameter is local to the DTE-modem interface and is used in other PDP
context-related commands. The range of values is 0 to 4.
GPRS multislot class number. It may be loser than the maximum possible class. Possible
values are 2, 8, 10, 12. Note that the range of values is dependent upon the modem.
Multislot
Class
2
8
10
12
The modem must be rebooted to activate the new setup except for <mode> 3, 5, 6
Rx
2
4
4
4
Number of Slots
Maximum
Tx
1
1
2
4
Sum
3
5
5
5
T
3
3
3
2
Minimum Number of
ta
T
2
1
1
1
tb
Slots
T
3
2
2
2
ra
T
1
1
1
1
rb
Chapter 15 – GPRS Commands
of MS
Type
1
1
1
1
168