101-1272 Rabbit Semiconductor, 101-1272 Datasheet - Page 112

• Manufacturer Part Number: 101-1272
• Description: KIT MESH NETWORK ADD-ON RCM4510W
• Manufacturer: Rabbit Semiconductor
• Type: Microprocessorr

Specifications of 101-1272

• Product: Modules
• Data Bus Width: 12 bit
• Processor Type: Rabbit 4000
• Sram: 512 KB
• Number Of I/os: 20
• Description/function: Computer Module
• Interface Type: Ethernet
• For Use With/related Products: RCM4510W
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Other names: 316-1158

D.2.1 Additional Reference Information
Check
module, the X-CTU utility, and the Digi
PRO
RCM4510W, but the general documentation about ZigBee and the use of AT commands
for the XBee
D.2.2 Update Digi
The firmware version used by the Digi
installed on the RCM4510W. If you have updated the RCM4510W firmware (or you have
a need to re-install the firmware on the Digi
the Digi
• Remember to record the extended PAN ID, NI, and other parameters you are using.
• Firmware of the type
1. Start X-CTU from the desktop icon and set the “PC Settings” tab to
2. On the “PC Settings” tab, check the “Enable API” box under “Host Setup.”
3. On the “PC Settings” tab, select the “USB Serial Port” and click “Test/Query.” You
4. Under the “Modem Configuration” tab click the “Read” button. X-CTU will now dis-
5. Click the “Read” button, select XB24-B as the Modem type; select ZIGBEE COORDI-
6. When the process is complete set the PANID, NI, and other parameters to the values
106
WARE
should see a response showing the Modem Type (XB 24 B) and the firmware version.
Click
Note that several USB serial ports could be listed. If you select a serial port without the
Digi
cation with modem … OK,” but the modem type will be unknown, and the firmware
version will be blank.
If you a get a message that X-CTU is unable to open the COM port, verify that you
selected the COM port with the “USB Serial Port,” then try unplugging the Digi
USB from the USB slot and plugging it back in. Now click “Test/Query” again.
play the networking and I/O parameters for the Digi
NATOR API as the Function Set, and 21… as the Version, then click “Write.”
you were using before the firmware was upgraded.
®
Modem: XBEE XB24-ZB
Function Set: ZIGBEE COORDINATOR API (do not select other settings)
Version: the version of the firmware included with the version of Dynamic C you are using
RF modules are presently not compatible with the XBeeRF module used with the
Digi’s Web site
®
CAUTION: Different firmware versions are likely to interact with the Dynamic C libraries
®
OK
XBee USB connected, the X-CTU response to “Test/Query.” will be “communi-
XBee USB is in the Dynamic C
in different ways. Rabbit has tested the firmware associated with a particular version of
Dynamic C for correct operation, and only this version is included on the Dynamic C
CD-ROM — do not use any other firmware versions with that version of Dynamic C.
flow control,
.
®
and the XBee PRO
®
for the latest information and documentation on the XBee RF
XBee USB Firmware
8
XB24-ZB_21….zip
data bits, parity
®
RF modules is relevant.
®
XBee USB must correspond to the firmware version
®
XBee USB. Note that the XBee
Utilities\X-CTU\MODEMFW
NONE
®
XBee USB), the corresponding firmware for
is used for the Digi
,
1
stop bit.
®
XBee USB.
®
XBee USB coordinator.
RabbitCore RCM4500W
9600
®
folder.
and the XBee
baud,
®
HARD-
XBee