XBIB-R Digi International/Maxstream, XBIB-R Datasheet - Page 31

• Manufacturer Part Number: XBIB-R
• Description: BOARD RS232 ZIGBEE MOD PRO
• Manufacturer: Digi International/Maxstream

Specifications of XBIB-R

• Design Resources: XBIB-R Schematic
• Accessory Type: Interface Board
• For Use With/related Products: XBee and XBee Pro Radios
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 3‐05. XBee‐PRO Commands ‐ Serial Interfacing
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
I/O Settings
Table 3‐06. XBee‐PRO Commands ‐ I/O Settings (sub‐category designated within {brackets})
XBee/XBee‐PRO™ OEM RF Modules ‐ 802.15.4 ‐ v1.xAx [2007.05.031]
AT
Command
PR (v1.x80*)
AT
Command
D8
D7 (v1.x80*)
D6 (v1.x80*)
D5 (v1.x80*)
D0 - D4
(v1.xA0*)
IU (v1.xA0*)
IT (v1.xA0*)
IS (v1.xA0*)
IO (v1.xA0*)
IC (v1.xA0*)
IR (v1.xA0*)
AV (v1.xA0*)
Command
Category
Serial
Interfacing
Command
Category
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
Name and Description
Pull-up Resistor Enable. Set/Read bitfield to configure internal pull-up resistor status
for I/O lines
Bitfield Map:
Bit set to “1” specifies pull-up enabled; “0” specifies no pull-up
Name and Description
DI8 Configuration. Select/Read options for the DI8 line (pin 9) of the RF module.
DIO7 Configuration. Select/Read settings for the DIO7 line (pin 12) of the RF module.
Options include CTS flow control and I/O line settings.
DIO6 Configuration. Select/Read settings for the DIO6 line (pin 16) of the RF module.
Options include RTS flow control and I/O line settings.
DIO5 Configuration. Configure settings for the DIO5 line (pin 15) of the RF module.
Options include Associated LED indicator (blinks when associated) and I/O line
settings.
(DIO4 -DIO4) Configuration. Select/Read settings for the following lines: AD0/DIO0
(pin 20), AD1/DIO1 (pin 19), AD2/DIO2 (pin 18), AD3/DIO3 (pin 17), AD4/DIO4 (pin 11).
Options include: Analog-to-digital converter, Digital Input and Digital Output.
I/O Output Enable. Disables/Enables I/O data received to be sent out UART. The data
is sent using an API frame regardless of the current AP parameter value.
Samples before TX. Set/Read the number of samples to collect before transmitting
data. Maximum number of samples is dependent upon the number of enabled inputs.
Force Sample. Force a read of all enabled inputs (DI or ADC). Data is returned through
the UART. If no inputs are defined (DI or ADC), this command will return error.
Digital Output Level. Set digital output level to allow DIO lines that are setup as
outputs to be changed through Command Mode.
DIO Change Detect. Set/Read bitfield values for change detect monitoring. Each bit
enables monitoring of DIO0 - DIO7 for changes. If detected, data is transmitted with
DIO data only. Any samples queued waiting for transmission will be sent first.
Sample Rate. Set/Read sample rate. When set, this parameter causes the module to
sample all enabled inputs at a specified interval.
ADC Voltage Reference. <XBee-PRO only> Set/Read ADC reference voltage switch.
© 2007 MaxStream, Inc.
bit 0 - AD4/DIO4 (pin11)
bit 1 - AD3 / DIO3 (pin17)
bit 2 - AD2/DIO2 (pin18)
bit 3 - AD1/DIO1 (pin19)
bit 4 - AD0 / DIO0 (pin20)
bit 5 - RTS / AD6 / DIO6 (pin16)
bit 6 - DTR / SLEEP_RQ / DI8 (pin9)
bit 7 - DIN/CONFIG (pin3)
Chapter 3 ‐ RF Module Configuration
Parameter Range
0 - 0xFF
Parameter Range
0 - 1
(1,2,4 & 5 n/a)
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
1 - 0xFF
8-bit bitmap (each bit
represents the level of an I/O
line setup as an output)
-
0 - 0xFF [bitfield]
0 - 0xFFFF [x 1 msec]
0 - 1
0 = Disabled
3 = DI
0 = Disabled
1 = CTS Flow Control
2 = (n/a)
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = RTS flow control
2 = (n/a)
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = Associated indicator
2 = ADC
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = (n/a)
2 = ADC
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = Enabled
0 = VREF pin
1 = Internal
Default
0xFF
Default
0
1
0
1
0
1
1
-
-
0 (disabled)
0
0
31