STEVAL-IPE010V1 STMicroelectronics, STEVAL-IPE010V1 Datasheet - Page 21

• Manufacturer Part Number: STEVAL-IPE010V1
• Description: KIT DEMO ENERGY METER STPMC1/S1
• Manufacturer: STMicroelectronics
• Type: Other Power Managementr

Specifications of STEVAL-IPE010V1

• Main Purpose: Power Management, Energy/Power Meter
• Embedded: No
• Utilized Ic / Part: STPMC1, STPMS1
• Maximum Operating Temperature: + 85 C
• Product: Power Management Development Tools
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Secondary Attributes: -
• Primary Attributes: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: STPMC1, STPMS1
• Other names: 497-10754

STPMC1
9.2
The calculator, thanks to its flexibility, can work in all worldwide distribution network
standards. By programming the SYS OTP bits, it is possible to implement the following
systems:
●
●
●
●
●
●
●
●
The results of all DSP units are available as pulse frequency on pin LED, MOP and MON,
which can also drive a stepper counter, and as states on the digital outputs of device or as
data bits in data records, which can be read from the device by means of SPI interface from
pins SDA, SNC, SCL and SYN. This system bus interface is also used during temporary or
permanent programming OTP bits and system signals or to execute a remote reset request.
A logic block common to all DSP units performs other operations like:
●
●
●
●
●
●
●
After the device is fully tested, configured and calibrated, a dedicated bit of the OTP block,
called TSTD, can be written permanently in order to prevent the change of any configuration
bit.
Power supply
The supply pins for the analog part are V
V low drop regulator, band-gap reference and bias generators.
From the V
used to power the OTP module and digital core. The V
for all the internal signals. 100 nF low ESR capacitors should be connected between V
and V
to the device.
The STPMC1 contains a power on reset (POR) detection circuit. If the V
than 2.5 V then the STPMC1 goes into an inactive state, all the functions are blocked
asserting a reset condition. This is useful to ensure correct device operation at power-up
and during power-down. The power supply monitor has built-in hysteresis and filtering,
which gives a high degree of immunity from false triggering due to noisy supplies.
A bandgap voltage reference (VBG) of 1.23 V ±1% is used as a reference voltage level
3-phase, 4-wire RSTN, 4-system RSTN (tamper);
3-phase, 4-wire RSTN, 3-system RST;
3-phase, 3-wire RST_, 3-system RST_ (tamper);
3-phase, 3-wire RST_, 2-system R_T_ (Aron);
2-phase, 3-wire _STN, 2-system _ST_ (America);
1-phase, 2-wire __TN, 2-system _ST_ (tamper coil:coil);
1-phase, 2-wire __TN, 2-system _ST_ (tamper coil:shunt);
1-phase, 2-wire __TN, 1-system __T_.
selecting the valid phase period result from which line frequency is computed in NDSP
unit
checking the equality of phase angles between all three phase voltages
preparing current values for compensation of external intermediate phase magnetic
influences
checking the sum of currents
computing intermediate phase voltages
combining the 3-phase status bits
performing a watchdog user function
SS
, and 1 µF between V
CC
pin a linear regulator generates the +1.8 V voltage supply level (V
DD
Doc ID 15728 Rev 4
and V
SSA
CC
. All these capacitors must be placed very close
and V
SS
. The V
SS
pin represents the reference point
CC
is the power input of the 1.8
Theory of operation
CC
supply is less
DD
) which is
CC
21/77