XR17D158IV-F Exar Corporation, XR17D158IV-F Datasheet - Page 24

• Manufacturer Part Number: XR17D158IV-F
• Description: IC UART PCI BUS OCTAL 144LQFP
• Manufacturer: Exar Corporation
• Type: IrDA or RS- 485r

Specifications of XR17D158IV-F

• Number Of Channels: 8
• Package / Case: 144-LQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 6.25 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Supply Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 5 V
• No. Of Channels: 8
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1292

XR17D158
UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART
MPIOINT [7:0] (default 0x00)
Enable multipurpose input pin interrupt. If the pin is selected by MPIOSEL as input then bit-0 enables input pin
0 for interrupt, and bit-7 enables input pin 7. No interrupt is enable if the pin is selected to be an output. The
interrupt is edge sensing and determined by MPIOINV and MPIOLVL registers. The MPIO interrupt clears after
a read to register MPIOLVL. The combination of MPIOLVL and MPIOINV determines the interrupt being active
low or active high, it’s level trigger. Logic 0 (default) disables the pin’s interrupt and logic 1 enables it.
MPIOLVL [7:0] (default 0x00)
Output pin level control and input level status. The status of the input pin(s) is read on this register and output
pins are controlled on this register. A logic 0 (default) sets the output to low and a logic 1 sets the output pin to
high. The MPIO interrupt will clear upon reading this register.
F
IGURE
MPIOINT [7:0]
MPIOLVL [7:0]
Read Input Level
MPIOINV [7:0]
(Input Inversion Enable =1)
MPIOLVL [7:0]
(Output Level)
MPIO3T [7:0]
(3-state Enable =1)
MPIOSEL [7:0]
(Select Input=1, Output=0 )
INT
8. M
ULTIPURPOSE INPUT
AND
Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
MPIO7
Multipurpose Input/Output Interrupt Enable
MPIO6
MPIO5 MPIO4 MPIO3 MPIO2 MPIO1 MPIO0
Rising Edge
Detection
MPIOINT Register
OR
/
OUTPUT INTERNAL CIRCUIT
1
0
24
AND
Pin [7:0]
MPIO
MPIOCKT
xr
REV. 1.2.2