USBLC6-2P6 STMicroelectronics, USBLC6-2P6 Datasheet
USBLC6-2P6
Specifications of USBLC6-2P6
Available stocks
Related parts for USBLC6-2P6
USBLC6-2P6 Summary of contents
Page 1
... Video line protection ■ Portable electronics Description The USBLC6-2SC6 and USBLC6-2P6 are monolithic application specific devices dedicated to ESD protection of high speed interfaces, such as USB 2.0, Ethernet links and video lines. The very low line capacitance secures a high level of signal integrity without compromising in protecting sensitive chips against the most stringent characterized ESD strikes ...
Page 2
... IEC 61000-4-2 contact discharge MIL STD883G-Method 3015 °C) amb Parameter Test conditions BUS 8/20 µs PP Any I/O pin to GND 8/20 µs PP Any I/O pin to GND = 1. 1. USBLC6-2 Value Unit -55 to +150 °C -40 to +125 °C 260 °C Value Unit Min. Typ. Max 150 1 ...
Page 3
... USBLC6-2 Figure 2. Capacitance versus voltage (typical values) C(pF) 3.0 C =I/O-GND O 2.5 2.0 1.5 C =I/O-I/O j 1.0 0.5 Data line voltage (V) 0.0 0.0 0.5 1.0 1.5 2.0 2.5 Figure 4. Relative variation of leakage current versus junction temperature (typical values =25° 100 10 T (° Figure 3. ...
Page 4
... Technical information 2 Technical information 2.1 Surge protection The USBLC6-2 is particularly optimized to perform surge protection based on the rail to rail topology. The clamping voltage TRANSIL with forward drop voltage and TRANSIL Calculation example We assume that the value of the dynamic resistance of the clamping diode is typically ...
Page 5
... TRANSIL 2.3 How to ensure good ESD protection While the USBLC6-2 provides high immunity to ESD surge, efficient protection depends on the layout of the board. In the same way, with the rail to rail topology, the track from data lines to I/O pins, from V possible to avoid overvoltages due to parasitic phenomena (see layout consideration) Figure 7 ...
Page 6
... The perturbed line will be more affected if it works with low voltage signal or high load impedance (few k ). 6/14 Figure 10. ESD response to IEC 61000-4-2 Vin Vout R G1 Line Line 2 DRIVERS This part of the (-15 kV air discharge RECEIVERS fact the real voltage at this point 2 G2 signal represents the effect of the G1 USBLC6 ...
Page 7
... Figure 13.). Figure 13. Analog crosstalk results As the USBLC6-2 is designed to protect high speed data lines, it must ensure a good transmission of operating signals. The frequency response information and shows that the USBLC6-2 is well suitable for data line transmission up to 480 Mbit/s while it works as a filter for undesirable signals like GSM (900 MHz) frequencies, for instance ...
Page 8
... Full Speed FS Closed High Speed HS Closed then open Figure 15. T1/E1/Ethernet protection 8/ USB connector BUS D+ D- GND USBLC6-2SC6 + 3. USB connector BUS D+ D- GND USBLC6-2P6 SW 2 Closed Open Open + 100nF SMP75 100nF SMP75-8 USBLC6 DOWNSTREAM Protecting TRANSCEIVER Bus Switch V BUS R X LS/ ...
Page 9
... USBLC6-2 2.6 PSpice model Figure 16. shows the PSpice model of one USBLC6-2 cell. In this model, the diodes are defined by the PSpice parameters given in Figure 16. PSpice model LI/O RI/O D+in LGND RGND GND LI/O RI/O D-in Note: This simulation model is available only for an ambient temperature of 27 °C. ...
Page 10
... Ordering information scheme 3 Ordering information scheme Figure 19. Ordering information scheme Product Designation Low capacitance Breakdown Voltage Volts Number of lines protected lines Packages SC6 = SOT23- SOT-666 10/14 USBLC6-2 USB xxx ...
Page 11
... USBLC6-2 4 Package information ● Epoxy meets UL94 order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label ...
Page 12
... Ref Figure 23. SOT23-6L marking 0.60 1.20 0.95 1.10 USBLC6-2 Dimensions Millimeters Inches Min. Typ. Max. Min. Typ. 0.90 1.45 0.035 0 0.10 0 0.90 1.30 0.035 0.35 0.50 0.014 0.09 0.20 0.004 2.80 3.05 0.11 1.50 1.75 0.059 0.95 0.037 2 ...
Page 13
... USBLC6-2 5 Ordering information Table 5. Ordering information Ordering code USBLC6-2SC6 USBLC6-2P6 6 Revision history Table 6. Document revision history Date 14-Mar-2005 07-Jun-2005 20-Mar-2008 Marking Package Weight UL26 SOT23-6L 16 SOT-666 2.9 mg Revision 1 First issue. 2 Format change to figure 3; no content changed. Added marking illustrations - Figures 21 and 23. Added ECOPACK statement ...
Page 14
... Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 14/14 Please Read Carefully: © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies www.st.com USBLC6-2 ...