MC9S08GB60CFU Freescale Semiconductor, MC9S08GB60CFU Datasheet - Page 181

• Manufacturer Part Number: MC9S08GB60CFU
• Description: IC MCU 60K FLASH 20MHZ 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GB60CFU

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

RE — Receiver Enable
RWU — Receiver Wakeup Control
SBK — Send Break
11.10.4 SCI x Status Register 1 (SCIxS1)
This register has eight read-only status flags. Writes have no effect. Special software sequences (that do
not involve writing to this register) are used to clear these status flags.
TDRE — Transmit Data Register Empty Flag
Freescale Semiconductor
When the SCI receiver is off, the RxD1 pin reverts to being a general-purpose port I/O pin.
This bit can be written to 1 to place the SCI receiver in a standby state where it waits for automatic
hardware detection of a selected wakeup condition. The wakeup condition is either an idle line between
messages (WAKE = 0, idle-line wakeup), or a logic 1 in the most significant data bit in a character
(WAKE = 1, address-mark wakeup). Application software sets RWU and (normally) a selected
hardware condition automatically clears RWU. Refer to
Operation,”
Writing a 1 and then a 0 to SBK queues a break character in the transmit data stream. Additional break
characters of 10 or 11 bit times of logic 0 are queued as long as SBK = 1. Depending on the timing of
the set and clear of SBK relative to the information currently being transmitted, a second break
character may be queued before software clears SBK. Refer to
Queued
TDRE is set out of reset and when a transmit data value transfers from the transmit data buffer to the
transmit shifter, leaving room for a new character in the buffer. To clear TDRE, read SCIxS1 with
TDRE = 1 and then write to the SCI data register (SCIxD).
1 = Receiver on.
0 = Receiver off.
1 = SCI receiver in standby waiting for wakeup condition.
0 = Normal SCI receiver operation.
1 = Queue break character(s) to be sent.
0 = Normal transmitter operation.
1 = Transmit data register (buffer) empty.
0 = Transmit data register (buffer) full.
Idle,”
for more details.
for more details.
Reset:
Read:
Write:
TDRE
Bit 7
1
Figure 11-9. SCI x Status Register 1 (SCIxS1)
= Unimplemented or Reserved
MC9S08GB/GT Data Sheet, Rev. 2.3
TC
6
1
RDRF
5
0
IDLE
4
0
Section 11.6.3, “Receiver Wakeup
OR
3
0
Section 11.5.2, “Send Break and
NF
2
0
SCI Registers and Control Bits
FE
1
0
Bit 0
PF
0
181