MC68HC705JP7CDW Freescale Semiconductor, MC68HC705JP7CDW Datasheet - Page 47

• Manufacturer Part Number: MC68HC705JP7CDW
• Description: IC MCU 8BIT 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MC68HC705JP7CDW

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SIO
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 22
• Program Memory Size: 6KB (6K x 8)
• Program Memory Type: OTP
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

5.5.4 COP Watchdog
A reset clears the COP watchdog timeout counter.
5.5.5 16-Bit Programmable Timer
A reset has these effects on the 16-bit programmable timer:
5.5.6 Serial Interface
A reset has these effects on the serial interface:
A reset, therefore, disables the SIOP and leaves the shared port B pins as general I/O. Any pending
interrupt flag is cleared and the SIOP interrupt is disabled. Also the baud rate defaults to the slowest rate.
5.5.7 Analog Subsystem
A reset has these effects on the analog subsystem:
A reset, therefore, connects the negative input of comparator 2 to the channel selection bus, which is
switched to V
input results in a positive output) and both are powered down. The current source and discharge device
on the PB0/AN0 pin is disabled and powered down. Any analog subsystem interrupt flags are cleared and
the analog interrupt is disabled. Direct drive by comparator 1 to the PB4 pin and the voltage offset to the
sample capacitor are disabled (if both are enabled by the OPT bit being set in the COPR).
5.5.8 External Oscillator and Internal Low-Power Oscillator
A reset presets the oscillator select bits (OM1 and OM2) in the interrupt status and control register (ISCR)
such that the device runs from the internal oscillator (OM1 = 0, OM2 = 1) which has these effects on the
oscillators:
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Initializes the timer counter registers (TMRH and TMRL) to a value of $FFFC
Initializes the alternate timer counter registers (ACRH and ACRL) to a value of $FFFC
Clears all the interrupt enables and the output level bit (OLVL) in the timer control register (TCR)
Does not affect the input capture edge bit (IEDG) in the TCR
Does not affect the interrupt flags in the timer status register (TSR)
Does not affect the input capture registers (ICRH and ICRL)
Does not affect the output compare registers (OCRH and OCRL)
Clears all bits in the SIOP control register (SCR)
Clears all bits in the SIOP status register (SSR)
Does not affect the contents of the SIOP data register (SDR)
Clears all the bits in the multiplex register (AMUX) bits except the hold switch bit (HOLD) which is
set
Clears all the bits in the analog control register (ACR)
Clears all the bits in the analog status register (ASR)
The internal low-power oscillator is enabled and selected.
The external oscillator is disabled.
The CPU bus clock is driven from the internal low-power oscillator.
SS
. Both comparators are set up as non-inverting (a higher positive voltage on the positive
MC68HC705JJ7 • MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
Reset States
47