ATMEGA323-8PC Atmel, ATMEGA323-8PC Datasheet - Page 104

• Manufacturer Part Number: ATMEGA323-8PC
• Description: IC AVR MCU 32K 8MHZ COM 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA323-8PC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: ATMEGA3238PC

The Two-wire Serial Interface
Bit Rate Register – TWBR
The Two-wire Serial Interface
Control Register – TWCR
104
ATmega323(L)
• Bits 7..0 – Two-wire Serial Interface Bit Rate Register
TWBR selects the division factor for the bit rate generator. The bit rate generator is a
frequency divider which generates the SCL clock frequency in the Master modes
according to the following equation:
•
•
•
•
Note:
TWBR should be set to a value higher than seven to ensure correct Two-wire Serial Bus
functionality. The bus alignment adjustment is automatically inserted by the Two-wire
Serial Interface, and ensures the validity of setup and hold times on the bus for any
TWBR value higher than 7. This adjustment may vary from 200 ns to 600 ns depending
on bus loads and drive capabilities of the devices connected to the bus.
• Bit 7 – TWINT: Two-wire Serial Interface Interrupt Flag
This bit is set by hardware when the Two-wire Serial Interface has finished its current
job and expects application software response. If the I-bit in the SREG and TWIE in the
TWCR Register are set (one), the MCU will jump to the Interrupt Vector at address
$026. While the TWINT Flag is set, the bus SCL clock line low period is stretched. The
TWINT Flag must be cleared by software by writing a logic one to it. Note that this flag is
not automatically cleared by hardware when executing the interrupt routine. Also note
that clearing this flag starts the operation of the Two-wire Serial Interface, so all
accesses to the Two-wire Serial Interface Address Register – TWAR, Two-wire Serial
Interface Status Register – TWSR, and Two-wire Serial Interface Data Register – TWDR
must be complete before clearing this flag.
• Bit 6 – TWEA: Two-wire Serial Interface Enable Acknowledge Flag
TWEA Flag controls the generation of the acknowledge pulse. If the TWEA bit is set, the
ACK pulse is generated on the Two-wire Serial Bus if the following conditions are met:
1. The device’s own slave address has been received.
2. A general call has been received, while the TWGCE bit in the TWAR is set.
3. A data byte has been received in Master Receiver or Slave Receiver mode.
Bit
$00 ($20)
Read/Write
Initial Value
Bit
$36 ($56)
Read/Write
Initial Value
Bit Rate = SCL frequency
f
TWBR
t
CK
A
Both the Receiver and the Transmitter can stretch the low period of the SCL line when
waiting for user response, thereby reducing the average bit rate.
TWBR7
TWINT
= CPU Clock frequency
= Contents of the Two-wire Serial Interface Bit Rate Register
= Bus alignment adjustment
R/W
R/W
7
0
7
0
TWBR6
TWEA
R/W
R/W
6
0
6
0
Bit Rate
TWBR5
TWSTA
R/W
R/W
5
0
5
0
=
TWSTO
TWBR4
---------------------------------------------------------- -
16
R/W
R/W
4
0
4
0
+
2(TWBR) + t
TWBR3
TWWC
f
R/W
CK
R
3
0
3
0
TWBR2
TWEN
A
R/W
R/W
f
2
0
2
0
CK
TWBR1
R/W
R
1
0
1
–
0
TWBR0
TWIE
R/W
R/W
1457G–AVR–09/03
0
0
0
0
TWBR
TWCR