ATTINY15L-1PC Atmel, ATTINY15L-1PC Datasheet - Page 34
![IC AVR MCU 1K FLASH 2.7V 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
ATTINY15L-1PC
Manufacturer Part Number
ATTINY15L-1PC
Description
IC AVR MCU 1K FLASH 2.7V 8DIP
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY15L-1PC
Core Processor
AVR
Core Size
8-Bit
Speed
1.6MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1KB (512 x 16)
Program Memory Type
FLASH
Eeprom Size
64 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Ram Size
-
Connectivity
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
The Watchdog Timer
The Watchdog Timer Control
Register – WDTCR
34
ATtiny15L
The Watchdog Timer is clocked from a separate On-chip Oscillator that runs at 1 MHz.
This is the typical value at V
values at other V
Reset interval can be adjusted from 16 to 2,048 ms, as shown in Table 15. The WDR
(Watchdog Reset) instruction resets the Watchdog Timer. Eight different clock cycle
periods can be selected to determine the reset period. If the reset period expires without
another Watchdog Reset, the ATtiny15L resets and executes from the Reset Vector.
For timing details on the Watchdog Reset, refer to page 17.
To prevent unintentional disabling of the Watchdog, a special turn-off sequence must be
followed when the Watchdog is disabled. Refer to the description of the Watchdog Timer
Control Register for details.
Figure 23. Watchdog Timer
• Bits 7..5 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and will always read as zero.
• Bit 4 – WDTOE: Watchdog Turn-off Enable
This bit must be set (one) when the WDE bit is cleared. Otherwise, the Watchdog will
not be disabled. Once set, hardware will clear this bit to zero after four clock cycles.
Refer to the description of the WDE bit for a Watchdog disable procedure.
• Bit 3 – WDE: Watchdog Enable
When the WDE is set (one), the Watchdog Timer is enabled and if the WDE is cleared
(zero), the Watchdog Timer function is disabled. WDE can be cleared only when the
WDTOE bit is set (one). To disable an enabled Watchdog Timer, the following proce-
dure must be followed:
Bit
$21
Read/Write
Initial Value
R
7
–
0
WATCHDOG
CC
RESET
levels. By controlling the Watchdog Timer prescaler, the Watchdog
1 MHz at Vcc = 5V
350 KHz at Vcc = 3V
WDP0
WDP1
WDP2
WDE
R
6
–
0
Oscillator
CC
= 5V. See “Typical Characteristics” on page 66 for typical
R
5
–
0
WDTOE
R/W
4
0
WDE
R/W
3
0
PRESCALER
WATCHDOG
MCU RESET
WDP2
R/W
2
0
WDP1
R/W
1
0
WDP0
R/W
0
0
1187H–AVR–09/07
WDTCR