UPD78F9222CS-CAC-A Renesas Electronics America, UPD78F9222CS-CAC-A Datasheet - Page 276
UPD78F9222CS-CAC-A
Manufacturer Part Number
UPD78F9222CS-CAC-A
Description
MCU 8BIT 4KB FLASH 20PIN
Manufacturer
Renesas Electronics America
Series
78K0S/Kx1+r
Datasheet
1.UPD78F9221MC-5A4-A.pdf
(418 pages)
Specifications of UPD78F9222CS-CAC-A
Core Processor
78K0S
Core Size
8-Bit
Speed
10MHz
Connectivity
LIN, UART/USART
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
15
Program Memory Size
4KB (4K x 8)
Program Memory Type
FLASH
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 276 of 418
- Download datasheet (3Mb)
18.6 Pin Connection on Board
provided on the target system. First provide a function that selects the normal operation mode or flash memory
programming mode on the board.
the same status as immediately after reset. Therefore, if the external device does not recognize the state immediately
after reset, the pins must be processed as described below.
18.6.1 X1 and X2 pins
pins are connected to an external device, a signal conflict occurs. To prevent the conflict of signals, isolate the
connection with the external device.
and thus communication may be disabled depending on the capacitor capacitance. Make sure to isolate the
connection with the capacitor during flash programming.
when it is difficult to isolate the resonator, while a crystal or ceramic resonator is selected as the system clock.
274
To write the flash memory on-board, connectors that connect the dedicated flash memory programmer must be
When the flash memory programming mode is set, all the pins not used for programming the flash memory are in
The state of the pins in the self programming mode is the same as that in the HALT mode.
The X1 and X2 pins are used as the serial interface of flash memory programming. Therefore, if the X1 and X2
Similarly, when a capacitor is connected to the X1 and X2 pins, the waveform during communication is changed,
Perform the following processing (1) and (2) when on-board programming is performed with the resonator mounted,
(1) Mount the minimum-possible test pads between the device and the resonator, and connect the programmer via
(2) Set the oscillation frequency of the communication clock for writing using the programming GUI of the
the test pad. Keep the wiring as short as possible (refer to Figure 18-4 and Table 18-3).
dedicated flash memory programmer. Research the series/parallel resonant and antiresonant frequencies of
the resonator used, and set the oscillation frequency so that it is outside the range of the resonant frequency
10% (refer to Figure 18-5 and Table 18-4).
High-speed internal oscillation clock
External clock
Crystal/ceramic oscillation
clock
Table 18-3. Clock to Be Used and Mounting of Test Pads
Figure 18-4. Example of Mounting Test Pads
Clock to Be Used
CHAPTER 18 FLASH MEMORY
Before resonator is mounted
After resonator is mounted
User’s Manual U16898EJ6V0UD
V
SS
X1
Test pad
X2
Not required
Required
Mounting of Test Pads
Related parts for UPD78F9222CS-CAC-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: