MC9S08RD32CDWE Freescale Semiconductor, MC9S08RD32CDWE Datasheet - Page 58

• Manufacturer Part Number: MC9S08RD32CDWE
• Description: IC MCU 32K FLASH 2K RAM 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08RD32CDWE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: S08RD
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 39
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08RG60E
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Resets, Interrupts, and System Configuration
The MC9S08RC/RD/RE/RG has these sources for reset:
Each of these sources, with the exception of the background debug forced reset, has an associated bit in
the system reset status register. Whenever the MCU enters reset, the reset pin is driven low for 34 internal
bus cycles where the internal bus frequency is one-half the OSC frequency. After the 34 cycles are
completed, the pin is released and will be pulled up by the internal pullup resistor, unless it is held low
externally. After the pin is released, it is sampled after another 38 cycles to determine whether the reset pin
is the cause of the MCU reset.
5.4
The COP watchdog is intended to force a system reset when the application software fails to execute as
expected. To prevent a system reset from the COP timer (when it is enabled), application software must
reset the COP timer periodically. If the application program gets lost and fails to reset the COP before it
times out, a system reset is generated to force the system back to a known starting point. The COP
watchdog is enabled by the COPE bit in SOPT (see
additional information). The COP timer is reset by writing any value to the address of SRS. This write does
not affect the data in the read-only SRS. Instead, the act of writing to this address is decoded and sends a
reset signal to the COP timer.
After any reset, the COP timer is enabled. This provides a reliable way to detect code that is not executing
as intended. If the COP watchdog is not used in an application, it can be disabled by clearing the COPE
bit in the write-once SOPT register. Also, the COPT bit can be used to choose one of two timeout periods
(2
and COPT, the user must write to write-once SOPT during reset initialization to lock in the settings. That
way, they cannot be changed accidentally if the application program gets lost.
The write to SRS that services (clears) the COP timer must not be placed in an interrupt service routine
(ISR) because the ISR could continue to be executed periodically even if the main application program
fails.
When the MCU is in active background mode, the COP timer is temporarily disabled.
5.5
Interrupts provide a way to save the current CPU status and registers, execute an interrupt service routine
(ISR), and then restore the CPU status so processing resumes where it was before the interrupt. Other than
the software interrupt (SWI), which is a program instruction, interrupts are caused by hardware events such
58
18
•
•
•
•
•
•
•
or 2
Power-on reset (POR)
Low-voltage detect (LVD)
Computer operating properly (COP) timer
Illegal opcode detect
Illegal address (16K and 8K devices only)
Background debug forced reset
The reset pin (RESET)
20
Computer Operating Properly (COP) Watchdog
Interrupts
cycles of the bus rate clock). Even if the application will use the reset default settings in COPE
MC9S08RC/RD/RE/RG Data Sheet, Rev. 1.11
Section 5.8.4, “System Options Register
Freescale Semiconductor
(SOPT),”
for