S9S08AW60E5MFDE Freescale Semiconductor, S9S08AW60E5MFDE Datasheet - Page 188

• Manufacturer Part Number: S9S08AW60E5MFDE
• Description: MCU 64K FLASH AUTO MONET 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08AW60E5MFDE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN Exposed Pad
• Controller Family/series: HCS08
• No. Of I/o's: 38
• Ram Memory Size: 2KB
• Cpu Speed: 40MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Chapter 11 Serial Communications Interface (S08SCIV2)
11.2.3
This register can be read or written at any time.
188
Reset
Field
TCIE
ILIE
TIE
RIE
RE
TE
7
6
5
4
3
2
W
R
SCI Control Register 2 (SCIxC2)
TIE
Transmit Interrupt Enable (for TDRE)
0 Hardware interrupts from TDRE disabled (use polling).
1 Hardware interrupt requested when TDRE flag is 1.
Transmission Complete Interrupt Enable (for TC)
0 Hardware interrupts from TC disabled (use polling).
1 Hardware interrupt requested when TC flag is 1.
Receiver Interrupt Enable (for RDRF)
0 Hardware interrupts from RDRF disabled (use polling).
1 Hardware interrupt requested when RDRF flag is 1.
Idle Line Interrupt Enable (for IDLE)
0 Hardware interrupts from IDLE disabled (use polling).
1 Hardware interrupt requested when IDLE flag is 1.
Transmitter Enable
0 Transmitter off.
1 Transmitter on.
TE must be 1 in order to use the SCI transmitter. Normally, when TE = 1, the SCI forces the TxD pin to act as an
output for the SCI system. If LOOPS = 1 and RSRC = 0, the TxD pin reverts to being a port B general-purpose
I/O pin even if TE = 1.
When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of
traffic on the single SCI communication line (TxD pin).
TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress.
Refer to
When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued
break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin.
Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin.
0 Receiver off.
1 Receiver on.
0
7
Section 11.3.2.1, “Send Break and Queued
TCIE
0
6
Table 11-4. SCIxC2 Register Field Descriptions
Figure 11-7. SCI Control Register 2 (SCIxC2)
RIE
0
5
MC9S08AW60 Data Sheet, Rev 2
ILIE
0
4
Description
Idle” for more details.
TE
3
0
RE
0
2
Freescale Semiconductor
RWU
0
1
SBK
0
0