ST7FLITE29F2M6TR STMicroelectronics, ST7FLITE29F2M6TR Datasheet - Page 111

• Manufacturer Part Number: ST7FLITE29F2M6TR
• Description: IC MCU 8BIT 8K FLASH 20-SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE29F2M6TR

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLIT2-COS/COM, ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel / 13 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 67. I2Cs_PutBuffer
Note: The above function is only for I2C_ITDRV_WITHOUTBUF_TX mode.
Caution:
– Any data transmitted before using this function will be neglected through dummy byte
Overflow condition: The overflow bytes are neglected through dummy bytes.
Table 68. I2Cs_PutByte
Function Name
Function Prototype
Behaviour Description
Input Parameter 1
Input Parameter 2
Output Parameters
Required Preconditions
Functions called
Postconditions
See also
Function Name
Function Prototype
Behaviour Description
Input Parameter
Output Parameters
Required Preconditions
Functions called
Postconditions
See also
* The maximum size of the buffer is under user control.
‘I2C interrupt driven’
I2Cs_PutBuffer
Void I2Cs_PutBuffer(unsigned char *PtrToBuffer, un-
signed char MaxSize)
Starts transmission of data from the user defined area by
initializing the transmission buffer for
I2C_ITDRV_WITHOUTBUF_TX mode
*PtrToBuffer
Start address of the user buffer
MaxSize
Size of the buffer
None
1. You must define I2C_ITDRV_WITHOUTBUF_TX mode
in ST7lib_config.h
2. I2C communication mode must be detected through the
I2Cs_GetCommMode
None
I2Cs_IsTransmitCompleted should be called to know the
current status of transmission
I2Cs_PutBuffer (I2C Polling mode)
I2Cs_PutByte
Void I2Cs_PutByte (unsigned char Tx_Byte)
Transmits single byte on the I2C bus
Tx_Byte
The byte to be transmit on the I2C bus
None
1) I2Cs_GetCommMode must have been called before
transmitting first byte to check whether the
I2Cs_TX_MODE is selected or not
2) Transmission of previous data has been taken success-
fully, which should be checked through the
I2Cs_IsTransmitCompleted
None
None
I2Cs_GetByte
Function Descriptions
111/235