AT91SAM7X512-AU Atmel, AT91SAM7X512-AU Datasheet - Page 459

• Manufacturer Part Number: AT91SAM7X512-AU
• Description: MCU ARM 512K HS FLASH 100-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X512-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 128 KB
• Interface Type: CAN, SPI, SSC, TWI, USART, USB
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7X-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• No. Of I/o's: 62
• Ram Memory Size: 128KB
• Cpu Speed: 55MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 4
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7X-EK - KIT EVAL FOR AT91SAM7X256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6120H–ATARM–17-Feb-09
banks of memory are used. While one is available for the microcontroller, the other one is locked
by the USB device.
Figure 34-10. Bank Swapping in Data OUT Transfers for Ping-pong Endpoints
When using a ping-pong endpoint, the following procedures are required to perform Data OUT
transactions:
1. The host generates a Data OUT packet.
2. This packet is received by the USB device endpoint. It is written in the endpoint’s FIFO
3. The USB device sends an ACK PID packet to the host. The host can immediately send
4. The microcontroller is notified that the USB device has received a data payload, polling
5. The number of bytes available in the FIFO is made available by reading RXBYTECNT
6. The microcontroller transfers out data received from the endpoint’s memory to the
7. The microcontroller notifies the USB peripheral device that it has finished the transfer
8. A third Data OUT packet can be accepted by the USB peripheral device and copied in
9. If a second Data OUT packet has been received, the microcontroller is notified by the
10. The microcontroller transfers out data received from the endpoint’s memory to the
Bank 0.
a second Data OUT packet. It is accepted by the device and copied to FIFO Bank 1.
RX_DATA_BK0 in the endpoint’s UDP_ CSRx register. An interrupt is pending for this
endpoint while RX_DATA_BK0 is set.
in the endpoint’s UDP_ CSRx register.
microcontroller’s memory. Data received is made available by reading the endpoint’s
UDP_ FDRx register.
by clearing RX_DATA_BK0 in the endpoint’s UDP_ CSRx register.
the FIFO Bank 0.
flag RX_DATA_BK1 set in the endpoint’s UDP_ CSRx register. An interrupt is pending
for this endpoint while RX_DATA_BK1 is set.
microcontroller’s memory. Data received is available by reading the endpoint’s UDP_
FDRx register.
1 st Data Payload
2 nd Data Payload
3 rd Data Payload
Microcontroller
Write and Read at the Same Time
AT91SAM7X512/256/128 Preliminary
Bank 0
Endpoint 1
Bank 1
Endpoint 1
Bank 0
Endpoint 1
Write
USB Device
Bank 0
Endpoint 1
Bank 1
Endpoint 1
Bank 0
Endpoint 1
Read
USB Bus
2 nd Data Payload
3 rd Data Payload
1 st Data Payload
Data IN Packet
Data IN Packet
Data IN Packet
459