AT90USB1286-AU Atmel, AT90USB1286-AU Datasheet - Page 377

• Manufacturer Part Number: AT90USB1286-AU
• Description: MCU AVR 128K FLASH 16MHZ 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB1286-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Controller Family/series: AVR USB
• No. Of I/o's: 48
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

29.6.9
29.6.10
29.6.11
7593K–AVR–11/09
Programming the Fuse High Bits
Programming the Extended Fuse Bits
Programming the Lock Bits
The algorithm for programming the Fuse High bits is as follows (refer to
Flash” on page 373
The algorithm for programming the Extended Fuse bits is as follows (refer to
Flash” on page 373
Figure 29-5. Programming the FUSES Waveforms
The algorithm for programming the Lock bits is as follows (refer to
page 373
The Lock bits can only be cleared by executing Chip Erase.
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. Set BS2, BS1 to “01”. This selects high data byte.
4. Give WR a negative pulse and wait for RDY/BSY to go high.
5. Set BS2, BS1 to “00”. This selects low data byte.
1. 1. A: Load Command “0100 0000”.
2. 2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. 3. Set BS2, BS1 to “10”. This selects extended data byte.
4. 4. Give WR a negative pulse and wait for RDY/BSY to go high.
5. 5. Set BS2, BS1 to “00”. This selects low data byte.
1. A: Load Command “0010 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs the Lock bit. If LB mode 3 is programmed
3. Give WR a negative pulse and wait for RDY/BSY to go high.
RESET +12V
(LB1 and LB2 is programmed), it is not possible to program the Boot Lock bits by any
External Programming mode.
RDY/BSY
PAGEL
XTAL1
DATA
for details on Command and Data loading):
XA1
XA0
BS1
BS2
WR
OE
0x40
A
for details on Command and Data loading):
for details on Command and Data loading):
DATA
C
Write Fuse Low byte
XX
0x40
A
DATA
C
Write Fuse high byte
XX
AT90USB64/128
“Programming the Flash” on
0x40
A
DATA
C
Write Extended Fuse byte
“Programming the
“Programming the
XX
377