AT89C51ID2-SLRUM Atmel, AT89C51ID2-SLRUM Datasheet - Page 73

• Manufacturer Part Number: AT89C51ID2-SLRUM
• Description: IC 8051 MCU 64K FLASH 44-PLCC
• Manufacturer: Atmel
• Series: 89Cr

Specifications of AT89C51ID2-SLRUM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 60MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: UART, SPI, TWI
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: AT89C51ID2-SLRUMTR

Entering Power-Down Mode
Exiting Power-Down Mode
Figure 26. Power-Down Exit Waveform Using INT1:0#
73
AT89C51ID2
INT1:0#
OSC
Active phase
and RAM contents are preserved. The status of the Port pins during Power-Down mode
is detailed in Table 57.
Note:
To enter Power-Down mode, set PD bit in PCON register. The AT89C51ID2 enters the
Power-Down mode upon execution of the instruction that sets PD bit. The instruction
that sets PD bit is the last instruction executed.
Note:
There are two ways to exit the Power-Down mode:
1. Generate an enabled external interrupt.
Note:
Note:
2. Generate a reset.
Note:
–
–
VCC may be reduced to as low as V
power dissipation. Take care, however, that VDD is not reduced until Power-Down mode
is invoked.
If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until
VCC is restored to the normal operating level.
The AT89C51ID2 provides capability to exit from Power-Down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and
restores the clocks to the CPU and peripherals. Using INTx# input,
execution resumes when the input is released (see Figure 26). Execution
resumes with the interrupt service routine. Upon completion of the interrupt
service routine, program execution resumes with the instruction immediately
following the instruction that activated Power-Down mode.
The external interrupt used to exit Power-Down mode must be configured as level sensi-
tive (INT0# and INT1#) and must be assigned the highest priority. In addition, the
duration of the interrupt must be long enough to allow the oscillator to stabilize. The exe-
cution will only resume when the interrupt is deasserted.
Exit from power-down by external interrupt does not affect the
content.
A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU
and peripherals. Program execution momentarily resumes with the
instruction immediately following the instruction that activated Power-Down
mode and may continue for a number of clock cycles before the internal
reset algorithm takes control. Reset initializes the AT89C51ID2 and vectors
the CPU to address 0000h.
During the time that execution resumes, the internal RAM cannot be accessed; however,
it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port
Power-down phase
Oscillator restart phase
RET
during Power-Down mode to further reduce
Active phase
SFRs
nor the internal RAM
4289C–8051–11/05