PIC14000T-04/SO Microchip Technology, PIC14000T-04/SO Datasheet - Page 47
![IC MCU OTP 4KX14 A/D 28SOIC](/photos/6/59/65909/150-28-soic_sml.jpg)
PIC14000T-04/SO
Manufacturer Part Number
PIC14000T-04/SO
Description
IC MCU OTP 4KX14 A/D 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 14r
Datasheets
1.PIC16LF627A-IP.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC14000-04SO.pdf
(153 pages)
4.PIC14000-04SO.pdf
(5 pages)
Specifications of PIC14000T-04/SO
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Connectivity
I²C
Peripherals
POR, Temp Sensor, WDT
Number Of I /o
20
Program Memory Size
7KB (4K x 14)
Program Memory Type
OTP
Ram Size
192 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 6 V
Data Converters
Slope A/D
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
28-SOIC (7.5mm Width)
Processor Series
PIC14000
Core
PIC
Data Bus Width
8 bit
Data Ram Size
192 B
Interface Type
SPI, UART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
22
Number Of Timers
1
Operating Supply Voltage
2.7 V to 6 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Development Tools By Supplier
ICE2000
Minimum Operating Temperature
0 C
On-chip Adc
14 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC14000T-04/SO
Manufacturer:
MICROCHIP
Quantity:
12 000
7.4
The I
one master. This is called multi-master. When two or
more masters try to transfer data at the same time,
arbitration and synchronization occur.
7.4.1
Arbitration takes place on the SDA line, while the SCL
line is high. The master which transmits a high when
the other master transmits a low loses arbitration
(Figure 7-11) and turns off its data output stage. A
master which lost arbitrating can generate clock pulses
until the end of the data byte where it lost arbitration.
When the master devices are addressing the same
device, arbitration continues into the data.
Masters that also incorporate the slave function, and
have lost arbitration must immediately switch over to
slave-receiver mode. This is because the winning
master-transmitter may be addressing it.
Arbitration is not allowed between:
• A repeated START
• A STOP and a data bit
• A repeated START and a STOP
Care needs to be taken to ensure that these conditions
do not occur.
7.4.2
Clock synchronization occurs after the devices have
started arbitration. This is performed using a
wired-AND connection to the SCL line. A high to low
transition on the SCL line causes the concerned
devices to start counting off their low period. Once a
device clock has gone low, it will hold the SCL line low
until its SCL high state is reached. The low to high
transition of this clock may not change the state of the
SCL line, if another device clock is still within its low
period. The SCL line is held low by the device with the
longest low period. Devices with shorter low periods
enter a high wait-state, until the SCL line comes high.
When the SCL line comes high, all devices start
counting off their high periods. The first device to
complete its high period will pull the SCL line low. The
SCA line high time is determined by the device with the
shortest high period. This is shown in the Figure 7-12.
1996 Microchip Technology Inc.
2
C protocol allows a system to have more than
Multi-Master Operation
ARBITRATION
CLOCK SYNCHRONIZATION
Preliminary
FIGURE 7-11: MULTI-MASTER
FIGURE 7-12: I
DATA 1
DATA 2
SDA
SCL
CLK
CLK
SCL
1
2
ARBITRATION (2 MASTERS)
SYNCHRONIZATION
2
C CLOCK
counter
reset
wait
state
transmitter 1 loses arbitration
PIC14000
DATA 1≠ SDA
DS40122B-page 47
start counting
HIGH period