ATMEGA168-15MZ Atmel, ATMEGA168-15MZ Datasheet - Page 195

• Manufacturer Part Number: ATMEGA168-15MZ
• Description: MCU AVR 16K FLASH 15MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA168-15MZ

• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 23
• Eeprom Size: 512 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Program Memory Size: 16KB (16K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: I²C, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: 2-Wire, SPI, USART, Serial
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 32QFN EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7530I–AVR–02/10
Note:
Assembly Code Example
C Code Example
USART_Init:
void USART_Init( unsigned int baud )
{
}
clr r18
out UBRRnH,r18
out UBRRnL,r18
; Setting the XCKn port pin as output, enables master mode.
sbi XCKn_DDR, XCKn
; Set MSPI mode of operation and SPI data mode 0.
ldi r18, (1<<UMSELn1)|(1<<UMSELn0)|(0<<UCPHAn)|(0<<UCPOLn)
out UCSRnC,r18
; Enable receiver and transmitter.
ldi r18, (1<<RXENn)|(1<<TXENn)
out UCSRnB,r18
; Set baud rate.
; IMPORTANT: The Baud Rate must be set after the transmitter is enabled!
out UBRRnH, r17
out UBRRnL, r18
ret
UBRRn = 0;
/* Setting the XCKn port pin as output, enables master mode. */
XCKn_DDR |= (1<<XCKn);
/* Set MSPI mode of operation and SPI data mode 0. */
UCSRnC = (1<<UMSELn1)|(1<<UMSELn0)|(0<<UCPHAn)|(0<<UCPOLn);
/* Enable receiver and transmitter. */
UCSRnB = (1<<RXENn)|(1<<TXENn);
/* Set baud rate. */
/* IMPORTANT: The Baud Rate must be set after the transmitter is enabled
*/
UBRRn = baud;
1. The example code assumes that the part specific header file is included. For I/O Registers
located in extended I/O map, "IN", "OUT", "SBIS", "SBIC", "CBI", and "SBI" instructions must
be replaced with instructions that allow access to extended I/O. Typically "LDS" and "STS"
combined with "SBRS", "SBRC", "SBR", and "CBR".
(1)
(1)
ATmega48/88/168 Automotive
195