PIC16LC924-04I/L Microchip Technology, PIC16LC924-04I/L Datasheet - Page 106

• Manufacturer Part Number: PIC16LC924-04I/L
• Description: IC MCU OTP 4KX14 LCD DVR 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC924-04I/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C, SPI
• Peripherals: LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 176 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 6 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• Core: PIC
• Processor Series: PIC16LC
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 8 MHz
• Data Ram Size: 176 B
• Data Rom Size: 176 B
• On-chip Adc: 8 bit, 5 Channel
• Number Of Programmable I/os: 25
• Number Of Timers: 3
• Operating Supply Voltage: 2.5 V to 6 V
• Mounting Style: SMD/SMT
• Height: 4.06 mm
• Interface Type: I2C, SPI
• Length: 24.33 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 6 V
• Supply Voltage (min): 2.5 V
• Width: 24.33 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC16C9XX
14.3
The PIC16CXX differentiates between various kinds of
reset:
• Power-on Reset (POR)
• MCLR Reset during normal operation
• MCLR Reset during SLEEP
• WDT Reset (normal operation)
Some registers are not affected in any reset condition;
their status is unknown on POR and unchanged in any
other reset. Most other registers are reset to a “reset
state” on Power-on Reset (POR), on the MCLR and
WDT Reset, and on MCLR Reset during SLEEP. They
are not affected by a WDT Wake-up, which is viewed as
FIGURE 14-7: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
DS30444E - page 106
Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin.
MCLR
OSC1
V
DD
2: See Table 14-3 for time-out situations.
Reset
RC OSC
On-chip
OST/PWRT
V
Module
(1)
detect
WDT
DD
rise
OST
PWRT
10-bit Ripple counter
WDT
10-bit Ripple counter
Time-out
Power-on Reset
External
Reset
SLEEP
Enable PWRT
Enable OST
the resumption of normal operation. The TO and PD
bits are set or cleared differently in different reset situ-
ations as indicated in Table 14-4. These bits are used
in software to determine the nature of the reset. See
Table 14-6 for a full description of reset states of all reg-
isters.
A simplified block diagram of the on-chip reset circuit is
shown in Figure 14-7.
The devices all have a MCLR noise filter in the MCLR
reset path. The filter will detect and ignore small pulses.
It should be noted that a WDT Reset does not drive
MCLR pin low.
(2)
(2)
1997 Microchip Technology Inc.
S
R
Q
Chip_Reset