DSPIC33FJ64MC706-I/PT Microchip Technology, DSPIC33FJ64MC706-I/PT Datasheet - Page 11
![IC DSPIC MCU/DSP 64K 64TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
DSPIC33FJ64MC706-I/PT
Manufacturer Part Number
DSPIC33FJ64MC706-I/PT
Description
IC DSPIC MCU/DSP 64K 64TQFP
Manufacturer
Microchip Technology
Series
dsPIC™ 33Fr
Datasheets
1.MA330013.pdf
(370 pages)
2.DSPIC33FJ12GP201-ISO.pdf
(90 pages)
3.DSPIC33FJ64MC506-IPT.pdf
(340 pages)
4.DSPIC33FJ64MC506-IPT.pdf
(30 pages)
Specifications of DSPIC33FJ64MC706-I/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
53
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 16x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TFQFP
Core Frequency
40MHz
Embedded Interface Type
ECAN, I2C, SPI, UART
No. Of I/o's
53
Flash Memory Size
64KB
Supply Voltage Range
3V To 3.6V
Operating Temperature Range
-40°C To
Package
64TQFP
Device Core
dsPIC
Family Name
dSPIC33
Maximum Speed
40 MHz
Operating Supply Voltage
3.3 V
Data Bus Width
16 Bit
Number Of Programmable I/os
53
Interface Type
CAN/I2C/SPI/UART
On-chip Adc
32-chx10-bit|32-chx12-bit
Number Of Timers
9
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC33FJ64MC706-I/PT
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
DSPIC33FJ64MC706-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
3.2
The programmer’s model, shown in Figure 3-2,
consists of 16 x 16-bit working registers (W0 through
W15), 2 x 40-bit accumulators (ACCA and ACCB),
Status Register (SR), Data Table Page register
(TBLPAG), Program Space Visibility Page register
(PSVPAG), DO and REPEAT registers (DOSTART,
DOEND, DCOUNT and RCOUNT) and Program
Counter (PC). The working registers can act as data,
address or offset registers. All registers are memory
mapped. W0 is the W register for all instructions that
perform file register addressing.
Some of these registers have a shadow register
associated with them (see the legend in Figure 3-2).
The shadow register is used as a temporary holding
register and can transfer its contents to or from its host
register upon some event occurring in a single cycle.
None of the shadow registers are accessible directly.
When a byte operation is performed on a working
register, only the Least Significant Byte of the target
register is affected. However, a benefit of memory
mapped working registers is that both the Least and
Most Significant Bytes can be manipulated through
byte-wide data memory space accesses.
© 2005 Microchip Technology Inc.
Programmer’s Model
Preliminary
W15 is the dedicated software Stack Pointer (SP). It is
automatically modified by exception processing and
subroutine calls and returns. However, W15 can be
referenced by any instruction in the same manner as all
other W registers. This simplifies the reading, writing
and manipulation of the Stack Pointer (e.g., creating
stack frames).
W14 has been dedicated as a Stack Frame Pointer, as
defined by the LNK and ULNK instructions. However,
W14 can be referenced by any instruction in the same
manner as all other W registers.
The Stack Pointer always points to the first available
free word and grows from lower addresses towards
higher addresses. It pre-decrements for stack pops
(reads) and post-increments for stack pushes (writes).
dsPIC33F
DS70155C-page 9