ATMEGA329V-8MUR Atmel, ATMEGA329V-8MUR Datasheet - Page 55

• Manufacturer Part Number: ATMEGA329V-8MUR
• Description: MCU AVR 32K FLASH 8MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA329V-8MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.2
12.2.1
12.2.2
2552K–AVR–04/11
Register Description
EICRA – External Interrupt Control Register A
External Interrupt Mask Register – EIMSK
The External Interrupt Control Register A contains control bits for interrupt sense control.
• Bit 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0
The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corre-
sponding interrupt mask are set. The level and edges on the external INT0 pin that activate the
interrupt are defined in
edges. If edge or toggle interrupt is selected, pulses that last longer than one clock period will
generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low level
interrupt is selected, the low level must be held until the completion of the currently executing
instruction to generate an interrupt.
Table 12-1.
• Bit 7 – PCIE3: Pin Change Interrupt Enable 3
When the PCIE3 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 3 is enabled. Any change on any enabled PCINT30..24 pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCINT3
Interrupt Vector. PCINT30..24 pins are enabled individually by the PCMSK3 Register.
This bit is reserved bit in ATmega329/649 and should always be written to zero.
• Bit 6 – PCIE2: Pin Change Interrupt Enable 2
When the PCIE2 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 2 is enabled. Any change on any enabled PCINT23..16 pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCINT2
Interrupt Vector. PCINT23..16 pins are enabled individually by the PCMSK2 Register.
This bit is reserved bit in ATmega329/649 and should always be written to zero.
Bit
(0x69)
Read/Write
Initial Value
Bit
Read/Write
Initial Value
ISC01
0
0
1
1
ISC00
PCIE3
Interrupt 0 Sense Control
R/W
R
7
–
0
7
0
0
1
0
1
PCIE2
R/W
Description
The low level of INT0 generates an interrupt request.
Any logical change on INT0 generates an interrupt request.
The falling edge of INT0 generates an interrupt request.
The rising edge of INT0 generates an interrupt request.
R
6
–
0
6
0
Table
PCIE1
12-1. The value on the INT0 pin is sampled before detecting
R/W
R
5
–
0
5
0
PCIE0
R/W
4
–
R
0
4
0
ATmega329/3290/649/6490
R
3
–
0
R
3
–
0
R
2
–
0
R
2
–
0
ISC01
R/W
1
0
R
1
–
0
ISC00
R/W
INT0
R/W
0
0
0
0
EICRA
EIMSK
55