PIC18F26K20-I/ML Microchip Technology, PIC18F26K20-I/ML Datasheet - Page 253

• Manufacturer Part Number: PIC18F26K20-I/ML
• Description: IC PIC MCU FLASH 32KX16 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26K20-I/ML

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3936Byte
• Cpu Speed: 64MHz
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: CCP, ECCP, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / Rohs Status: Details

18.3.1
The EUSART module supports automatic detection
and calibration of the baud rate.
In the Auto-Baud Detect (ABD) mode, the clock to the
BRG is reversed. Rather than the BRG clocking the
incoming RX signal, the RX signal is timing the BRG.
The Baud Rate Generator is used to time the period of
a received 55h (ASCII “U”) which is the Sync character
for the LIN bus. The unique feature of this character is
that it has five rising edges including the Stop bit edge.
Setting the ABDEN bit of the BAUDCON register starts
the auto-baud calibration sequence (Figure 18.3.2).
While the ABD sequence takes place, the EUSART
state machine is held in Idle. On the first rising edge of
the receive line, after the Start bit, the SPBRG begins
counting up using the BRG counter clock as shown in
Table 18-6. The fifth rising edge will occur on the RX pin
at the end of the eighth bit period. At that time, an
accumulated value totaling the proper BRG period is
left in the SPBRGH:SPBRG register pair, the ABDEN
bit is automatically cleared, and the RCIF interrupt flag
is set. A read operation on the RCREG needs to be
performed to clear the RCIF interrupt. RCREG content
should be discarded. When calibrating for modes that
do not use the SPBRGH register the user can verify
that the SPBRG register did not overflow by checking
for 00h in the SPBRGH register.
The BRG auto-baud clock is determined by the BRG16
and BRGH bits as shown in Table 18-6. During ABD,
both the SPBRGH and SPBRG registers are used as a
16-bit counter, independent of the BRG16 bit setting.
While calibrating the baud rate period, the SPBRGH
FIGURE 18-6:
 2010 Microchip Technology Inc.
BRG Value
BRG Clock
ABDEN bit
RCIF bit
(Interrupt)
SPBRGH
RCREG
SPBRG
RX pin
RCIDL
Note 1:
Read
AUTO-BAUD DETECT
Set by User
The ABD sequence requires the EUSART module to be configured in Asynchronous mode.
XXXXh
AUTOMATIC BAUD RATE CALIBRATION
0000h
Start
bit 0
XXh
XXh
Edge #1
bit 1
bit 2
Edge #2
and SPBRG registers are clocked at 1/8th the BRG
base clock rate. The resulting byte measurement is the
average bit time when clocked at full speed.
TABLE 18-6:
PIC18F2XK20/4XK20
BRG16
Note:
Note 1: If the WUE bit is set with the ABDEN bit,
bit 3
0
0
1
1
2: It is up to the user to determine that the
3: During
bit 4
Edge #3
BRGH
During the ABD sequence, SPBRG and
SPBRGH registers are both used as a 16-bit
counter, independent of BRG16 setting.
auto-baud detection will occur on the byte
following the Break character (see
Section 18.3.3
Break”).
incoming character baud rate is within the
range of the selected BRG clock source.
Some combinations of oscillator frequency
and EUSART baud rates are not possible.
auto-baud counter starts counting at 1.
Upon
sequence, to achieve maximum accuracy,
subtract 1 from the SPBRGH:SPBRG
register pair.
0
1
0
1
bit 5
BRG COUNTER CLOCK RATES
completion
the
BRG Base
bit 6
Edge #4
F
F
F
F
Clock
OSC
OSC
OSC
OSC
auto-baud
bit 7
/64
/16
/16
/4
“Auto-Wake-up
of
DS41303G-page 253
Stop bit
Edge #5
the
Auto Cleared
process,
BRG ABD
001Ch
F
F
F
F
1Ch
00h
OSC
OSC
OSC
Clock
OSC
auto-baud
/512
/128
/128
/32
the
on