ATTINY45-15SZ Atmel, ATTINY45-15SZ Datasheet - Page 151

• Manufacturer Part Number: ATTINY45-15SZ
• Description: MCU AVR 4K FLASH 15MHZ 8-SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY45-15SZ

• Package / Case: 8-SOIC (3.9mm Width)
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 6
• Eeprom Size: 256 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Program Memory Size: 4KB (4K x 8)
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 22-1.
Notes:
22.2
Figure 22-1. External Clock Drive Waveforms
7598H–AVR–07/09
Symbol
I
CC
(6)
1. All DC Characteristics contained in this data sheet result from actual silicon characterization.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (8 mA at V
5. Although each I/O port can source more than the test conditions (8 mA at V
6. All I/O modules are turned off (PRR = 0xFF) for all I
7. Brown-Out Detection (BOD) disabled.
External Clock Drive Waveforms
ditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Power Supply Current
Power-down mode
DC Characteristics T
(7)
V
IL1
V
IH1
A
= -40°C to 125°C, V
Active 4MHz, V
Active 8MHz, V
Active 16MHz, V
Idle 4MHz, V
Idle 8MHz, V
Idle 16MHz, V
WDT enabled, V
WDT disabled, V
WDT enabled, V
WDT disabled, V
Condition
CC
CC
CC
CC
CC
= 3V
= 5V
CC
CC
CC
CC
CC
= 5V
= 3V
= 5V
= 3V
= 5V
= 5V
= 3V
= 5V
CC
CC
= 2.7V to 5.5V (unless otherwise noted)
values.
Min.
(2)
CC
= 5V, 5 mA at V
CC
= 5V, 5 mA at V
Typ.
1.25
0.4
1.2
2.5
10
5
5
2
9
3
CC
ATtiny25/45/85
= 3V) under steady state con-
CC
Max.
0.5
= 3V) under steady state
10
15
30
24
50
36
3
2
5
(1)
(3)
.
Units
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
151