PIC12F615-I/MS Microchip Technology, PIC12F615-I/MS Datasheet - Page 88
![IC PIC MCU FLASH 1KX14 8MSOP](/photos/6/59/65932/mfg_150_c04-111_ms_8-msop_sml.jpg)
PIC12F615-I/MS
Manufacturer Part Number
PIC12F615-I/MS
Description
IC PIC MCU FLASH 1KX14 8MSOP
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Datasheets
1.PIC12F609T-ISN.pdf
(212 pages)
2.PIC12F609T-ISN.pdf
(26 pages)
3.PIC12F609T-ISN.pdf
(8 pages)
4.PIC12F615-ESN.pdf
(168 pages)
Specifications of PIC12F615-I/MS
Core Size
8-Bit
Program Memory Size
1.75KB (1K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
20MHz
Number Of I /o
5
Program Memory Type
FLASH
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Controller Family/series
PIC12
No. Of I/o's
6
Ram Memory Size
64Byte
Cpu Speed
20MHz
No. Of Timers
3
Processor Series
PIC12F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
64 B
Interface Type
RS-232, USB
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
5
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 4 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
APGRD004 - REF DESIGN MOD AUTO AMBNT LIGHTAC162083 - HEADER MPLAB ICD2 PIC16F616 8/14AC164325 - MODULE SKT FOR 8MSOPXLT08DFN2 - SOCKET TRANSITION ICE 14DIP/8DFN
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC12F615-I/MS
Manufacturer:
RICHTEK
Quantity:
5 400
Part Number:
PIC12F615-I/MS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC12F609/615/12HV609/615
10.4.2
When any PWM mode is used, the application
hardware must use the proper external pull-up and/or
pull-down resistors on the PWM output pins.
The CCP1M<1:0> bits of the CCP1CON register allow
the user to choose whether the PWM output signals are
active-high or active-low for each PWM output pin (P1A
and P1B). The PWM output polarities must be selected
before the PWM pin output drivers are enabled.
Changing the polarity configuration while the PWM pin
output drivers are enable is not recommended since it
may result in damage to the application circuits.
The P1A and P1B output latches may not be in the proper
states when the PWM module is initialized. Enabling the
PWM pin output drivers at the same time as the
Enhanced PWM modes may cause damage to the
application circuit. The Enhanced PWM modes must be
enabled in the proper Output mode and complete a full
PWM cycle before configuring the PWM pin output
drivers. The completion of a full PWM cycle is indicated
by the TMR2IF bit of the PIR1 register being set as the
second PWM period begins.
DS41302A-page 86
Note:
START-UP CONSIDERATIONS
When the microcontroller is released from
Reset, all of the I/O pins are in the
high-impedance state. The external cir-
cuits must keep the power switch devices
in the OFF state until the microcontroller
drives the I/O pins with the proper signal
levels or activates the PWM output(s).
Preliminary
© 2006 Microchip Technology Inc.