PIC12F510-E/SN Microchip Technology, PIC12F510-E/SN Datasheet - Page 71
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12F510-E/SN
Manufacturer Part Number
PIC12F510-E/SN
Description
IC PIC MCU FLASH 1KX14 8SOIC
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Datasheets
1.PIC12F510-ISN.pdf
(124 pages)
2.PIC12F510-ISN.pdf
(8 pages)
3.PIC12F510-ISN.pdf
(20 pages)
Specifications of PIC12F510-E/SN
Core Size
8-Bit
Program Memory Size
1.5KB (1K x 12)
Core Processor
PIC
Speed
8MHz
Peripherals
POR, WDT
Number Of I /o
5
Program Memory Type
FLASH
Ram Size
38 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
8-SOIC (3.9mm Width)
Controller Family/series
PIC12
No. Of I/o's
6
Ram Memory Size
38Byte
Cpu Speed
8MHz
No. Of Timers
1
Digital Ic Case Style
SOIC
Processor Series
PIC12F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
38 B
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
5
Number Of Timers
1
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DV164101, DV164120, DM163029
Minimum Operating Temperature
- 40 C
On-chip Adc
8 bit, 3 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC162070 - HEADER INTRFC MPLAB ICD2 8/14P
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
Details
10.9
A device may be powered down (Sleep) and later
powered up (wake-up from Sleep Reset).
10.9.1
The Power-Down mode is entered by executing a
SLEEP instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the TO bit (STATUS<4>) is set, the PD
bit (STATUS<3>) is cleared and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, driving low or high-impedance).
For lowest current consumption while powered down,
all input pins should be at V
MCLR/V
enabled.
10.9.2
The device can wake-up from Sleep through one of the
following events:
1.
2.
3.
4.
These events cause a device Reset. The TO, PD,
CWUF and GPWUF/RBWUF bits can be used to deter-
mine the cause of device Reset. The TO bit is cleared
if a WDT time-out occurred (and caused wake-up). The
PD bit, which is set on power-up, is cleared when
SLEEP is invoked. The CWUF bit indicates a change in
comparator output state while the device was in Sleep.
The GPWUF/RBWUF bit indicates a change in state
while in Sleep at pins GP0/RB0, GP1/RB1, GP3/RB3
or RB4 (since the last file or bit operation on GP/RB
port).
© 2007 Microchip Technology Inc.
Note:
Note:
An external Reset input on (GP3/RB3)/MCLR/
V
A Watchdog Timer Time-out Reset (if WDT was
enabled).
A change-on-input pin GP0/RB0, GP1/RB1,
GP3/RB3 or RB4 when wake-up on change is
enabled.
A change in the comparator ouput bits, C1OUT
and C2OUT (if comparator wake-up is enabled).
PP
PP
Power-Down Mode (Sleep)
pin when configured as MCLR.
pin must be at a logic high level if MCLR is
SLEEP
A device Reset generated by a WDT
time-will not drive the MCLR pin low.
WAKE-UP FROM SLEEP RESET
Caution: Right before entering Sleep,
read the input pins. When in Sleep, wake-
up occurs when the values at the pins
change from the state they were in at the
last reading. If a wake-up on change
occurs and the pins are not read before
reentering Sleep, a wake-up will occur
immediately even if no pins change while
in Sleep mode.
DD
or V
SS
and (GP3/RB3)/
The WDT is cleared when the device wakes from
Sleep, regardless of the wake-up source.
10.10 Program Verification/Code
If the code protection bit has not been programmed, the
on-chip program memory can be read out for
verification purposes.
The first 64 locations and the last location (OSCCAL)
can be read, regardless of the code protection bit
setting.
The last memory location can be read regardless of the
code protection bit setting on the PIC12F510/16F506
devices.
10.11 ID Locations
Four memory locations are designated as ID locations
where the user can store checksum or other code
identification numbers. These locations are not
accessible during normal execution, but are readable
and writable during Program/Verify.
Use only the lower 4 bits of the ID locations and always
set the upper 4 bits as ‘1’s. The upper 4 bits are
unimplemented.
These locations can be read regardless of the code
protect setting.
Note 1: Caution: Right before entering Sleep,
PIC12F510/16F506
2: For 16F506 only.
Protection
read
register(s) CM1CON0 and CM2CON0.
When in Sleep, wake-up occurs when the
comparator
C2OUT change from the state they were
in at the last reading. If a wake-up on
comparator change occurs and the pins
are not read before re-entering Sleep, a
wake-up will occur immediately, even if
no pins change while in Sleep mode.
the
comparator
output
bit
DS41268D-page 69
C1OUT
Configuration
and