C8051F064-GQ Silicon Laboratories Inc, C8051F064-GQ Datasheet - Page 278

• Manufacturer Part Number: C8051F064-GQ
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F064-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 59
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 59
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F060DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit, 1 Channel
• On-chip Dac: 12 bit, 2 Channel
• No. Of I/o's: 59
• Ram Memory Size: 4352Byte
• Cpu Speed: 25MHz
• No. Of Timers: 5
• Rohs Compliant: Yes
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F06x
• Maximum Speed: 25 MHz
• Data Rom Size: 64 KB
• A/d Bit Size: 16 bit
• A/d Channels Available: 1
• Height: 1.05 mm
• Length: 14 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 14 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1219 - KIT EVAL FOR C8051F064
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1218

C8051F060/1/2/3/4/5/6/7
23.1. Enhanced Baud Rate Generation
The UART1 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 23.2), which is not user-
accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see
Timer with Auto-Reload” on page
at two times the desired baud rate. Note that Timer 1 may be clocked by one of five sources: SYSCLK,
SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, or the external oscillator clock / 8. For any given Timer 1 clock
source, the UART1 baud rate is determined by Equation 23.1.
Where T1
value). Timer 1 clock frequency is selected as described in
page
through Table 23.6. Note that the internal oscillator may still generate the system clock when the external
oscillator is driving Timer 1 (see
278
287. A quick reference for typical baud rates and system clock frequencies is given in Table 23.1
CLK
is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
Detected
Start
RX Timer
Section “24.1. Timer 0 and Timer 1” on page 287
UartBaudRate
Figure 23.2. UART1 Baud Rate Logic
289). The Timer 1 reload value should be set so that overflows will occur
Timer 1
TH1
TL1
Equation 23.1. UART1 Baud Rate
Overflow
Overflow
Rev. 1.2
=
------------------------------ -

256 T1H
T1
–
CLK
Section “24.1. Timer 0 and Timer 1” on
2
2
Section “24.1.3. Mode 2: 8-bit Counter/

UART1

1
-- -
2
RX Clock
TX Clock
for more details).