ST72F325K4T6 STMicroelectronics, ST72F325K4T6 Datasheet - Page 159

• Manufacturer Part Number: ST72F325K4T6
• Description: MCU 8BIT 16KB FLASH/ROM 32-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F325K4T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7232X-SK/RAIS, ST72325-D/RAIS, ST7MDT20-DVP3, ST7MDT20J-EMU3, ST7MDT20M-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: 497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5605

12.8 I/O PORT PIN CHARACTERISTICS
12.8.1 General Characteristics
Subject to general operating conditions for V
Figure 79. Unused I/Os configured as input
Notes:
1. Data based on characterization results, not tested in production.
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.
3. When the current limitation is not possible, the V
tion. A positive injection is induced by V
on page 143
4. Configuration not recommended, all unused pins must be kept at a fixed voltage: using the output mode of the I/O for
example and leaving the I/O unconnected on the board or an external pull-up or pull-down resistor (see
peak current value taken at a fixed V
production. This value depends on V
5. The R
scribed in
6. To generate an external interrupt, a minimum pulse width has to be applied on an I/O port pin configured as an external
interrupt source.
ΣI
I
Symbol
INJ(PIN)
t
t
Note: I/O can be left unconnected if it is configured as output
(0 or 1) by the software. This has the advantage of
INJ(PIN)
greater EMC robustness and lower cost.
t
r(IO)out
f(IO)out
w(IT)in
V
R
C
V
V
I
I
hys
PU
S
IH
L
IO
IL
3)
PU
3)
Figure
pull-up equivalent resistor is based on a resistive transistor (corresponding I
Input low level voltage
Input high level voltage
Schmitt trigger voltage hysteresis
Injected Current on PB0 (Flash de-
vices only)
Injected Current on an I/O pin
Total injected current (sum of all I/O
and control pins)
Input leakage current
Static current consumption
Weak pull-up equivalent resistor
I/O pin capacitance
Output high to low level fall time
Output low to high level rise time
External interrupt pulse time
for more details.
80).
V
DD
Parameter
10kΩ
10kΩ
UNUSED I/O PORT
UNUSED I/O PORT
1)
1)
DD
IN
IN
value, based on design simulation and technology characteristics, not tested in
and temperature values.
>V
6)
ST7XXX
ST7XXX
DD
5)
1)
1)
2)
while a negative injection is induced by V
CMOS ports
V
V
Floating input mode
V
C
Between 10% and 90%
IN
DD
DD
SS
IN
L
=50pF
=
maximum must be respected, otherwise refer to I
≤
, f
=5V
V
V
OSC
SS
IN
Conditions
≤
V
, and T
DD
Figure 80. Typical I
V
DD
=5V
A
4)
unless otherwise specified.
90
80
70
60
50
40
30
20
10
0
2
0.7xV
2.5
Min
50
0
1
Ta=140°C
Ta=95°C
Ta=25°C
Ta=-45°C
3
DD
PU
3.5
IN
vs. V
PU
<V
V dd(V)
Typ
400
120
0.7
25
25
5
4
SS
current characteristics de-
DD
. Refer to
4.5
with V
0.3xV
5
Max
± 25
INJ(PIN)
Figure
250
± 4
+4
±1
ST72325xx
5.5
section 12.2.2
DD
IN
=V
79). Static
specifica-
6
159/197
SS
Unit
t
mA
CPU
μA
kΩ
pF
ns
V