PIC16F636-I/ST Microchip Technology, PIC16F636-I/ST Datasheet - Page 71

• Manufacturer Part Number: PIC16F636-I/ST
• Description: IC MCU FLASH 2KX14 14TSSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F636-I/ST

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 14-TSSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, LVD, POR, WDT
• Number Of I /o: 11
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232/SPI/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Package: 14TSSOP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162057 - MPLAB ICD 2 HEADER 14DIP
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7.7
Response time is the minimum time, after selecting a
new reference voltage or input source, before the
comparator output is ensured to have a valid level. If
the internal reference is changed, the maximum delay
of the internal voltage reference must be considered
when using the comparator outputs. Otherwise, the
maximum delay of the comparators should be used
(Table 15-7).
7.8
The comparators and voltage reference, if enabled
before entering Sleep mode, remain active during
Sleep. This results in higher Sleep currents than shown
in the power-down specifications. The additional
current consumed by the comparator and the voltage
reference is shown separately in the specifications. To
minimize power consumption while in Sleep mode, turn
off the comparator, CM<2:0> = 111 and voltage
reference, VRCON<7> = 0.
REGISTER 7-3:
© 2005 Microchip Technology Inc.
Comparator Response Time
Operation During Sleep
bit 7
bit 6
bit 5
bit 4
bit 3-0
VRCON – VOLTAGE REFERENCE CONTROL REGISTER (ADDRESS: 99h)
bit 7
VREN: CV
1 = CV
0 = CV
Unimplemented: Read as ‘0’
VRR: CV
1 = Low range
0 = High range
Unimplemented: Read as ‘0’
VR<3:0>: CV
When VRR = 1:
CV
When VRR = 0:
CV
Legend:
R = Readable bit
- n = Value at POR
R/W-0
VREN
REF
REF
REF
REF
= (VR<3:0>/24) * V
= V
REF
REF
DD
circuit powered on
circuit powered down, no I
/4 + (VR<3:0>/32) * V
Range Selection bit
REF
Enable bit
U-0
—
Value Selection bits 0
R/W-0
PIC12F635/PIC16F636/639
VRR
DD
Preliminary
W = Writable bit
‘1’ = Bit is set
DD
DD
R/W-0
—
While the comparator is enabled during Sleep, an
interrupt will wake-up the device. If the GIE bit
(INTCON<7>) is set, the device will jump to the
interrupt vector (0004h) and if clear, continues
execution with the next instruction. If the device wakes
up from Sleep, the contents of the CMCON0, CMCON1
and VRCON registers are not affected.
7.9
A device Reset forces the CMCON0, CMCON1 and
VRCON registers to their Reset states. This forces the
comparator module to be in the Comparator Reset
mode, CM<2:0> = 000 and the voltage reference to its
OFF state. Thus, all potential inputs are analog inputs
with the comparator and voltage reference disabled to
consume the smallest current possible.
drain and CV
VR<3:0>
Effects of a Reset
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
VR3
15
REF
= V
R/W-0
SS
VR2
x = Bit is unknown
R/W-0
VR1
DS41232B-page 69
R/W-0
VR0
bit 0