C8051F310-GQ Silicon Laboratories Inc, C8051F310-GQ Datasheet - Page 103

• Manufacturer Part Number: C8051F310-GQ
• Description: IC 8051 MCU 16K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F31xr

Specifications of C8051F310-GQ

• Core Size: 8-Bit
• Program Memory Size: 16KB (16K x 8)
• Oscillator Type: Internal
• Core Processor: 8051
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 29
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• No. Of I/o's: 29
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Digital Ic Case: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1445 - ADAPTER PROGRAM TOOLSTICK F310336-1329 - KIT REF DESIGN SENSORLESS BLDC336-1253 - DEV KIT FOR C8051F310/F311
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1252

8.4.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruc-
tion that sets the bit completes execution. In Stop mode the internal oscillator, CPU, and all digital peripher-
als are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral (including
the external oscillator circuit) may be shut down individually prior to entering Stop Mode. Stop mode can
only be terminated by an internal or external reset. On reset, the CIP-51 performs the normal reset
sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the
MCD timeout of 100 µsec.
Bits7–2: GF5–GF0: General Purpose Flags 5–0.
Bit1:
Bit0:
GF5
R/W
Bit7
These are general purpose flags for use under software control.
STOP: Stop Mode Select.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: CPU goes into Stop mode (internal oscillator stopped).
IDLE: Idle Mode Select.
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: CPU goes into Idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial
Ports, and Analog Peripherals are still active.)
GF4
R/W
Bit6
SFR Definition 8.12.
GF3
R/W
Bit5
GF2
R/W
Bit4
Rev. 1.7
GF1
R/W
Bit3
PCON: Power Control
C8051F310/1/2/3/4/5/6/7
GF0
R/W
Bit2
STOP
R/W
Bit1
IDLE
R/W
Bit0
SFR Address:
00000000
Reset Value
0x87
103