MC9S08AC8CFGE Freescale Semiconductor, MC9S08AC8CFGE Datasheet - Page 309

• Manufacturer Part Number: MC9S08AC8CFGE
• Description: IC MCU 8BIT 8K FLASH 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08AC8CFGE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: S08AC
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 700 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 3
• Operating Supply Voltage: - 0.3 V to + 5.8 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08AC60E, DEMOACEX, DEMOACKIT, DCF51AC256, DC9S08AC128, DC9S08AC16, DC9S08AC60, DEMO51AC256KIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

1
2
3
4
5
6
7
8
9
10
Freescale Semiconductor
Num
Typical values are based on characterization data at V
Self-clocked mode frequency is the frequency that the DCO generates when the FLL is open-loop.
Loss of reference frequency is the reference frequency detected internally, which transitions the ICG into self-clocked mode if
it is not in the desired range.
Loss of DCO frequency is the DCO frequency detected internally, which transitions the ICG into FLL bypassed external mode
(if an external reference exists) if it is not in the desired range.
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period of time required for the FLL to lock after entering FLL engaged internal or external
modes. If a crystal/resonator is being used as the reference, this specification assumes it is already running.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via V
a given interval.
See
See
18
Figure
Figure
C
C
P
P
A-9.
A-9.
MC9S08ACxx: Internal oscillator deviation from
S9S08AWxxA: Internal oscillator deviation from
(V
trimmed frequency
V
V
trimmed frequency
V
V
V
DD
DD
DD
DDA
DD
DD
= 2.7 – 5.5 V, (constant temperature)
= 5.0 V ±10%, –40° C to 125°C
= 2.7 – 5.5 V, (constant temperature)
= 5.0 V ±10%, –40° C to 85°C
= 5.0 V ±10%, –40° C to 125°C
= V
DDA
Table A-11. ICG Frequency Specifications (continued)
(min) to V
Characteristic
9
10
DDA
and V
MC9S08AC16 Series Data Sheet, Rev. 8
DDA
SSA
(max), Temperature Range = –40 to 125°C Ambient)
and variation in crystal oscillator frequency increase the C
DD
= 5.0V, 25°C unless otherwise stated.
Appendix A Electrical Characteristics and Timing Specifications
Symbol
ACC
ACC
int
int
Min
—
—
—
—
—
Typ
± 0.5
± 0.5
±0.5
±0.5
±0.5
1
Jitter
Max
±1.5
±1.5
±2.0
±2
±2
percentage for
ICGOUT
Unit
%
%
.
309