ADUC7024BCPZ62 Analog Devices Inc, ADUC7024BCPZ62 Datasheet - Page 36

• Manufacturer Part Number: ADUC7024BCPZ62
• Description: IC MCU FLSH 62K ANLG I/O 64LFCSP
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7024BCPZ62

• Core Size: 16/32-Bit
• Program Memory Size: 62KB (62K x 8)
• Design Resources: Sensing Low-g Acceleration Using ADXL345 Digital Accelerometer Connected to ADuC7024 (CN0133)
• Core Processor: ARM7
• Speed: 44MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: PLA, PWM, PSM, Temp Sensor, WDT
• Number Of I /o: 30
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LFCSP
• Controller Family/series: (ARM7) ADUC
• No. Of I/o's: 30
• Ram Memory Size: 8KB
• Cpu Speed: 44MHz
• No. Of Timers: 4
• Digital Ic Case Style: LFCSP
• Embedded Interface Type: I2C, SPI, UART
• Rohs Compliant: Yes
• Package: 64LFCSP EP
• Device Core: ARM7TDMI
• Family Name: ADuC7xxx
• Maximum Speed: 44 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 30
• Interface Type: I2C/SPI/UART
• On-chip Adc: 10-chx12-bit
• On-chip Dac: 2-chx12-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

ADuC7019/20/21/22/24/25/26/27/28/29
•
•
INTERRUPT LATENCY
The worst-case latency for a fast interrupt request (FIQ)
consists of the following:
•
•
•
•
DDI0029G, ARM7TDMI Technical Reference Manual
DDI-0100, ARM Architecture Reference Manual
The longest time the request can take to pass through the
synchronizer
The time for the longest instruction to complete (the
longest instruction is an LDM) that loads all the registers
including the PC
The time for the data abort entry
The time for FIQ entry
Rev. C | Page 36 of 96
At the end of this time, the ARM7TDMI executes the instruc-
tion at 0x1C (FIQ interrupt vector address). The maximum
total time is 50 processor cycles, which is just under 1.2 μs in a
system using a continuous 41.78 MHz processor clock.
The maximum interrupt request (IRQ) latency calculation is
similar but must allow for the fact that FIQ has higher priority
and may delay entry into the IRQ handling routine for an
arbitrary length of time. This time can be reduced to 42 cycles if
the LDM command is not used. Some compilers have an option
to compile without using this command. Another option is to run
the part in thumb mode where the time is reduced to 22 cycles.
The minimum latency for FIQ or IRQ interrupts is a total of
five cycles, which consist of the shortest time the request can
take through the synchronizer plus the time to enter the
exception mode.
Note that the ARM7TDMI always runs in ARM (32-bit) mode
when in privileged modes, for example, when executing
interrupt service routines.