ADUC843BSZ62-5 Analog Devices Inc, ADUC843BSZ62-5 Datasheet - Page 63

• Manufacturer Part Number: ADUC843BSZ62-5
• Description: IC ADC 12BIT W/FLASH MCU 52-MQFP
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC8xxr

Specifications of ADUC843BSZ62-5

• Core Size: 8-Bit
• Program Memory Size: 62KB (62K x 8)
• Oscillator Type: Internal
• Core Processor: 8052
• Speed: 16.78MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: DMA, PSM, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 4.75 V ~ 5.25 V
• Data Converters: A/D 8x12b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-MQFP, 52-PQFP
• Controller Family/series: (8052) ADUC
• No. Of I/o's: 34
• Ram Memory Size: 2KB
• Cpu Speed: 16.78MHz
• No. Of Timers: 3
• No. Of Pwm: RoHS Compliant
• Package: 52MQFP
• Device Core: 8052
• Family Name: ADuC8xx
• Maximum Speed: 16.78 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 34
• Interface Type: I2C/SPI/UART
• On-chip Adc: 8-chx12-bit
• On-chip Dac: 2-chx12-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T2CON
SFR Address
Power-On Default
Bit Addressable
Table 30. T2CON SFR Bit Designations
Bit No.
7
6
5
4
3
2
1
0
Timer/Counter 2 Data Registers
Timer/Counter 2 also has two pairs of 8-bit data registers
associated with it. These are used as both timer data registers
and as timer capture/reload registers.
TH2 and TL2
Timer 2, data high byte and low byte.
SFR Address = CDH, CCH, respectively.
RCAP2H and RCAP2L
Timer 2, capture/reload byte and low byte.
SFR Address = CBH, CAH, respectively.
Name
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
CNT2
CAP2
Description
Timer 2 Overflow Flag.
Set by hardware on a Timer 2 overflow. TF2 cannot be set when either RCLK = 1 or TCLK = 1.
Cleared by user software.
Timer 2 External Flag.
Set by hardware when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.
Cleared by user software.
Receive Clock Enable Bit.
Set by the user to enable the serial port to use Timer 2 overflow pulses for its receive clock in serial port Modes 1 and 3.
Cleared by the user to enable Timer 1 overflow to be used for the receive clock.
Transmit Clock Enable Bit.
Set by the user to enable the serial port to use Timer 2 overflow pulses for its transmit clock in serial port Modes 1 and 3.
Cleared by the user to enable Timer 1 overflow to be used for the transmit clock.
Timer 2 External Enable Flag.
Set by the user to enable a capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being
used to clock the serial port.
Cleared by the user for Timer 2 to ignore events at T2EX.
Timer 2 Start/Stop Control Bit.
Set by the user to start Timer 2.
Cleared by the user to stop Timer 2.
Timer 2 Timer or Counter Function Select Bit.
Set by the user to select counter function (input from external T2 pin).
Cleared by the user to select timer function (input from on-chip core clock).
Timer 2 Capture/Reload Select Bit.
Set by the user to enable captures on negative transitions at T2EX if EXEN2 = 1.
Cleared by the user to enable autoreloads with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1.
When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to autoreload on Timer 2 overflow.
Timer/Counter 2 Control Register
C8H
00H
Yes
Rev. 0 | Page 63 of 88
ADuC841/ADuC842/ADuC843