ATMEGA16A-PU Atmel, ATMEGA16A-PU Datasheet - Page 237

• Manufacturer Part Number: ATMEGA16A-PU
• Description: MCU AVR 16K FLASH 16MHZ 40-PDIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 40PDIP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

24.5.2
8154B–AVR–07/09
Boundary-scan and the Two-wire Interface
Figure 24-4. General Port Pin Schematic Diagram
Note:
The 2 Two-wire Interface pins SCL and SDA have one additional control signal in the scan-
chain; Two-wire Interface Enable – TWIEN. As shown in
a tri-state buffer with slew-rate control in parallel with the ordinary digital port pins. A general
scan cell as shown in
Notes:
1. See Boundary-scan description for details.
1. A separate scan chain for the 50 ns spike filter on the input is not provided. The ordinary scan
2. Make sure the OC and TWIEN signals are not asserted simultaneously, as this will lead to
Pxn
support for digital port pins suffice for connectivity tests. The only reason for having TWIEN in
the scan path, is to be able to disconnect the slew-rate control buffer when doing boundary-
scan.
drive contention.
PUD:
PUExn:
OCxn:
ODxn:
IDxn:
SLEEP:
Figure 24-9
IDxn
PULLUP DISABLE
PULLUP ENABLE for pin Pxn
OUTPUT CONTROL for pin Pxn
OUTPUT DATA to pin Pxn
INPUT DATA from pin Pxn
SLEEP CONTROL
PUExn
is attached to the TWIEN signal.
SLEEP
OCxn
(1)
SYNCHRONIZER
ODxn
WDx:
RDx:
WPx:
RRx:
RPx:
CLK
D
L
Q
Q
I/O
Figure
:
D
WRITE DDRx
READ DDRx
WRITE PORTx
READ PORTx REGISTER
READ PORTx PIN
I/O CLOCK
PINxn
Q
Q
24-5, the TWIEN signal enables
RESET
RESET
Q
Q
Q
Q
PORTxn
DDxn
CLR
CLR
D
D
ATmega16A
CLK
PUD
WDx
RDx
WPx
RRx
RPx
I/O
237