DSPIC30F2010-20I/MM Microchip Technology, DSPIC30F2010-20I/MM Datasheet - Page 13

• Manufacturer Part Number: DSPIC30F2010-20I/MM
• Description: IC DSPIC MCU/DSP 12K 28QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-20I/MM

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F2010-20I/MMG; DSPIC30F201020IMM; DSPIC30F201020IMM

21. Module: Motor Control PWM – PWM
22. Module: I/O Port – Port Pin Multiplexed
23. Module: FRC
© 2008 Microchip Technology Inc.
If the PTDIR bit is set (when PTMR is counting
down), and the CPU execution is halted (after a
breakpoint is reached), PTMR will start counting
up as if PTDIR was zero.
Work around
None.
If the user application enables the auto-baud
feature in the UART module, the I/O pin
multiplexed with the IC1 (Input Capture) pin cannot
be used as a digital input.
Work around
None.
Internal FRC accuracy is outside the specification
documented in “Electrical Characteristics”,
Table 22-17 “AC Characteristics: Internal RC
Accuracy” of the “dsPIC30F2010 Data Sheet”
(DS70118).
The actual internal FRC accuracy is:
• ±4% for 25°C
• ±5% for -40°C and 85°C
• ±6% for 125°C
Counter Register
with IC1
24. Module: I
25. Module: Timer
26. Module: PLL Lock Status Bit
If there are two I
them is acting as the Master receiver and the other
as the Slave transmitter. If both devices are
configured for 10-bit addressing mode, and have
the same value in the A10 and A9 bits of their
addresses, then when the Slave select address is
sent from the Master, both the Master and Slave
acknowledge it. When the Master sends out the
read operation, both the Master and the Slave
enter into Read mode and both of them transmit
the data. The resultant data will be the ANDing of
the two transmissions.
Work around
In all I
A10 and A9 should be different.
When the timer is being operated in Asynchronous
mode using the secondary oscillator (32.768 kHz)
and the device is put into Sleep mode, a clock
switch to any other oscillator mode before putting
the device to Sleep prevents the timer from waking
the device from Sleep.
Work around
Do not clock switch to any other oscillator mode if
the timer is being used in Asynchronous mode
using the secondary oscillator (32.768 kHz).
The PLL LOCK Status bit (OSCCON<5>) can
occasionally get cleared and generate an
oscillator failure trap even when the PLL is still
locked and functioning correctly.
Work around
The user application must include an oscillator
failure trap service routine. In the trap service
routine, first inspect the status of the Clock Failure
Status bit (OSCCON<3>). If this bit is clear, return
from the trap service routine immediately and
continue program execution.
2
C devices, the addresses as well as bits
2
dsPIC30F2010
C
2
C devices on the bus, one of
DS80186J-page 13