ATMEGA8515L-8PU Atmel, ATMEGA8515L-8PU Datasheet - Page 36

• Manufacturer Part Number: ATMEGA8515L-8PU
• Description: IC AVR MCU 8K 8MHZ 3V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515L-8PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 35
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP W
• Controller Family/series: AVR MEGA
• No. Of I/o's: 35
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Low-frequency Crystal
Oscillator
36
ATmega8515(L)
Table 8. Start-up Times for the Crystal Oscillator Clock Selection (Continued)
Notes:
To use a 32.768 kHz watch crystal as the clock source for the device, the Low-fre-
quency Crystal Oscillator must be selected by setting the CKSEL Fuses to “1001”. The
crystal should be connected as shown in Figure 19. By programming the CKOPT Fuse,
the user can enable internal capacitors on XTAL1 and XTAL2, thereby removing the
need for external capacitors. The internal capacitors have a nominal value of 36 pF.
When this Oscillator is selected, start-up times are determined by the SUT Fuses as
shown in Table 9.
Table 9. Start-up Times for the Low-frequency Crystal Oscillator Clock Selection
Note:
CKSEL0
SUT1..0
00
01
10
11
1
1
1
1. These options should only be used when not operating close to the maximum fre-
2. These options are intended for use with ceramic resonators and will ensure fre-
1. These options should only be used if frequency stability at start-up is not important
quency of the device, and only if frequency stability at start-up is not important for the
application. These options are not suitable for crystals.
quency stability at start-up. They can also be used with crystals when not operating
close to the maximum frequency of the device, and if frequency stability at start-up is
not important for the application.
for the application.
SUT1..0
from Power-down
Start-up Time
01
10
11
1K CK
1K CK
32K CK
from Power-down
(1)
(1)
Start-up Time
16K CK
16K CK
16K CK
Additional Delay from
Reset (V
4.1 ms
65 ms
65 ms
Additional Delay from
CC
Reset (V
Reserved
= 5.0V)
4.1 ms
65 ms
CC
–
= 5.0V)
Recommended Usage
Fast rising power or BOD
enabled
Slowly rising power
Stable frequency at start-up
Recommended
Usage
Crystal Oscillator,
BOD enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator,
slowly rising power
2512F–AVR–12/03