PIC18LF24J11-I/SS Microchip Technology, PIC18LF24J11-I/SS Datasheet - Page 339

• Manufacturer Part Number: PIC18LF24J11-I/SS
• Description: IC PIC MCU FLASH 16K 2V 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF24J11-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 31 KHz
• Number Of Programmable I/os: 16
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DM183033, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.3.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTAx<5>) or the Continuous Receive
Enable bit, CREN (RCSTAx<4>). Data is sampled on
the RXx pin on the falling edge of the clock.
If enable bit, SREN, is set, only a single word is
received. If enable bit, CREN, is set, the reception is
continuous until CREN is cleared. If both bits are set,
then CREN takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 19-13:
© 2009 Microchip Technology Inc.
RC6/TX1/CK1/RP17
RC6/TX1/CK1/RP17
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0. This example is equally applicable
Initialize the SPBRGHx:SPBRGx registers for
the appropriate baud rate. Set or clear the
BRG16 bit, as required, to achieve the desired
baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
pin (TXCKP = 0)
pin (TXCKP = 1)
SDO1/RP18 pin
RC7/RX1/DT1/
to EUSART2 (RPn1/TX2/CK2 and RPn2/RX2/DT2).
(Interrupt)
RCREG1
CREN bit
RC1IF bit
bit SREN
SREN bit
Write to
EUSART SYNCHRONOUS MASTER
RECEPTION
Read
Q2
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
bit 0
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
bit 2
bit 3
PIC18F46J11 FAMILY
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RCxIE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
Interrupt flag bit, RCxIF, will be set when
reception is complete and an interrupt will be
generated if the enable bit, RCxIE, was set.
Read the RCSTAx register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREGx register.
bit, CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit 4
bit 5
bit 6
DS39932C-page 339
bit 7
Q1 Q2 Q3 Q4
‘0’